Chrysler 300 SRT8 2010 User Manual Download Page 226 | Manualshive

Page: 226 / 449

background image

to seek up and the left switch to seek down. The radio
will remain tuned to the new station until you make
another selection. Holding either button will bypass
stations without stopping until you release it.

Voice Recognition System (Radio) — If Equipped

Refer to “Voice Recognition System (VR)” in Section 3.

Voice Recognition Button uconnect™ phone — If
Equipped

Press this button to operate the uconnect™ phone feature
(if equipped). Refer to “uconnect™ phone” in Section 3.

If your vehicle is not equipped with or this feature is not
available on your vehicle, a “Not Equipped With
UConnect” message will display on the radio screen.

Phone Button uconnect™ phone — If Equipped

Press this button to operate the uconnect™ phone feature
(if equipped). Refer to “uconnect™ phone” in Section 3.

If your vehicle is not equipped with or this feature is not
available on your vehicle, a “Not Equipped With
UConnect” message will display on the radio screen.

TIME Button

Press the TIME button to alternate display of the time
and radio frequency.

Clock Setting Procedure

1. Press and hold the TIME button until the hours blink.

2. Adjust the hours by turning the right side TUNE/
SCROLL control knob.

3. After adjusting the hours, press the right side TUNE/
SCROLL control knob to set the minutes. The minutes
will begin to blink.

4. Adjust the minutes using the right side TUNE/
SCROLL control knob. Press the TUNE/SCROLL control
knob to save time change.

226

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
224
225
226
227
228
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: J-Top Pages: 2

Brand: Harmar Mobility Pages: 10

Brand: Porsche Pages: 144

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: Honda Pages: 208

Brand: Tachosys Pages: 28

Brand: ConWys AG Pages: 16

Brand: Maserati Pages: 302

Brand: TATA Motors Pages: 308

Brand: Westin Pages: 3

Brand: Kolpin Pages: 6

Brand: Curt Group Pages: 2

Brand: Toyota Pages: 26

Halo Pole Mount

Brand: Charge Amps Pages: 14

Brand: Scosche Pages: 32

Brand: Scion Pages: 58

Brand: Roadefend Pages: 15

Brand: LaserLine Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands