Chrysler 300 SRT8 2010 User Manual Download Page 74 | Manualshive

Page: 74 / 449

background image

the child restraint belt path and then buckle it. This
should stow the seat belt out of the reach of an
inquisitive child. Remind all children in the vehicle
that the seat belts are not toys and should not be
played with, and never leave your child unattended in
the vehicle.

WARNING!

Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.

Installing Child Restraints Using the Vehicle Seat
Belts

The passenger seat belts are equipped with either cinch-
ing latch plates or Automatic Locking Retractors (ALRs),
which are designed to keep the lap portion tight around

the child restraint so that it is not necessary to use a
locking clip. Pulling up on the shoulder portion of the
lap/shoulder belt will tighten the belt. The cinching latch
plate will keep the belt tight; however, any seat belt
system will loosen with time, so check the belt occasion-
ally and pull it tight if necessary.

The seat belt must be in the Automatic Locking Mode in
order to enable a child restraint to be tightly installed.
Refer to “Automatic Locking Mode” in this section. A
locking clip should not be necessary once the automatic
locking feature is enabled. Position the shoulder and lap
belt on the child restraint. The automatic locking retractor
is activated by first attaching the child seat, then pulling
all of the webbing out of the retractor, then allowing the
webbing to retract back into the retractor. Tighten web-
bing. To release, simply unbuckle the seat belt by de-
pressing the button, allowing the webbing to retract into
the retractor.

74

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
72
73
74
75
76
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: IAME Pages: 17

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: TrailFX Pages: 6

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: Trailboss Pages: 8

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

Brand: Skoda Pages: 281

HU-4421-XL-SDK01

Brand: FALCON RIDGE Pages: 5

Brand: MULTILIFT Pages: 62

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands