Chrysler 300 SRT8 2010 User Manual Download Page 256 | Manualshive

Page: 256 / 449

background image

Vacation Storage

Anytime you store your vehicle, or keep it out of service
(i.e., vacation) for two weeks or more, run the air
conditioning system at idle for about five minutes in the
fresh air and high blower setting. This will ensure
adequate system lubrication to minimize the possibility
of compressor damage when the system is started again.

Window Fogging

Interior fogging on the windshield can be quickly re-
moved by turning the mode selector to defrost. The
Defrost/Floor mode can be used to maintain a clear
windshield and provide sufficient heating. If side win-
dow fogging becomes a problem, increase blower speed.
Vehicle windows tend to fog on the inside in mild but
rainy or humid weather.

NOTE:

Recirculate without A/C should not be used for

long periods, as fogging may occur.

Outside Air Intake

Make sure the air intake, located directly in front of the
windshield, is free of obstructions such as leaves. Leaves
collected in the air intake may reduce airflow, and if they
enter the plenum, they could plug the water drains. In
Winter months, make sure the air intake is clear of ice,
slush, and snow.

A/C Air Filter — If Equipped

The climate control system filters outside air containing
dust, pollen and some odors. Strong odors cannot be
totally filtered out. Refer to “Maintenance Procedures” in
Section 7 for filter replacement instructions.

256

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
254
255
256
257
258
...
»

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

Brand: ULTIMATE SPEED Pages: 19

witty park XEV6 Series

Brand: hager Pages: 9

Brand: Zavoli Pages: 26

Brand: Triumph Pages: 86

Brand: Kia Pages: 385

Brand: Kolpin Pages: 25

Brand: Metra Electronics Pages: 2

Brand: EUFAB Pages: 12

Brand: Jeep Pages: 1528

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Brand: TATA Motors Pages: 136

Brand: Cadillac Pages: 20

Brand: Improved Racing Pages: 17

Brand: cam Pages: 6

Brand: SSV Works Pages: 2

Brand: Ranger design Pages: 22

Brand: Front Runner Pages: 7

Truck 2500 2018

Brand: RAM Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands