manualshive.com logo in svg

Chrysler 300 SRT8 2010, User Manual

The 2010 Chrysler 300 SRT8 is a powerful and stylish sedan that demands attention on the road. To help you get the most out of this exceptional vehicle, we offer a detailed User Manual that you can easily download for free from our website. Explore its features and unleash the potential of your Chrysler 300 SRT8 today.

Share
Download
background image

Using Electronic Speed Control on Hills

NOTE:

The Electronic Speed Control system maintains

speed up and down hills. A slight speed change on
moderate hills is normal.

The automatic transmission will downshift while climb-
ing uphill or descending downhill. This downshift is
necessary to maintain vehicle set speed.
On steep hills, a greater speed loss or gain may occur, so
it may be preferable to drive without Electronic Speed
Control.

WARNING!

Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your ve-
hicle could go too fast for the conditions and you
could lose control. An accident could be the result. Do
not use Electronic Speed Control in heavy traffic or on
roads that are winding, icy, snow-covered or slippery.

PARKSENSE

姞

REAR PARK ASSIST

The ParkSense

威

Rear Park Assist system is a driver aid

that senses for obstacles behind the vehicle. Refer to
ParkSense

威

System Usage Precautions for limitations of

this system and recommendations.

ParkSense

威

is active when the driver shifts the transmis-

sion into the REVERSE position, and the parking brake is
not applied, and the vehicle speed is less than 10 mph
(16 km/h).

ParkSense

威

can be turned on or off through the Electronic

Vehicle Information Center (EVIC) when the vehicle is in
PARK. Refer to “Personal Settings (Customer-Program-
mable Features)” under “Electronic Vehicle Information
Center (EVIC)” in Section 4.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

153

Summary of Contents for 300 SRT8 2010


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 SRT8 2010

PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Brand: PUTCO Pages: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Brand: Westfalia Pages: 18
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Brand: Axxess Pages: 8
Jeep Cherokee 1977 Owner'S Manual preview
Cherokee 1977
Brand: Jeep Pages: 136
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Brand: RAM Pages: 174
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Brand: Volvo Pages: 262
Yakima RimROC Instructions Manual preview
RimROC
Brand: Yakima Pages: 12
Axxess AXDSPX-VW1 Installation Instructions Manual preview
AXDSPX-VW1
Brand: Axxess Pages: 16
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Brand: Rugged Ridge Pages: 3
Thule PORTAGE 819 Instructions Manual preview
PORTAGE 819
Brand: Thule Pages: 12
Joie i-Level Instruction Manual preview
i-Level
Brand: Joie Pages: 53
Honda CRV 2015 Navigation Manual preview
CRV 2015
Brand: Honda Pages: 253
Toyota 2018 yaris Vehicle Instruction Card preview
2018 yaris
Brand: Toyota Pages: 11
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Brand: Griffin Technology Pages: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Brand: Mitsubishi Pages: 919
Scion 2013 iQ Warranty & Maintenance Manual preview
2013 iQ
Brand: Scion Pages: 58
Alfa Romeo Stelvio 2019 User Manual preview
Stelvio 2019
Brand: Alfa Romeo Pages: 268
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Brand: chinavasion Pages: 3

Brands by name

Popular brands

Load more brands