CET PMC-592, User Manual, Page: 138 / 177

137
CET Electric Technology
6) Self-Read Time is applied to Max Demand Log and Max/Min Log. There are two types of Self-Read Time :

A zero value indicates that the transfer will happen at 00:00 of the first day of every month.

A non-zero value indicates that the transfer will happen at a specific time based on the formula [Hour+Day*100]
where 0≤Hour≤23 and 1≤Day≤28. For example, the value 2812 means that the Max Demand of Current Month will
be transferred to the Max Demand of Last Month register at 12:00pm on the 28th day of each month.
7) Phase x Color used to display waveform by each phase on the Web Interface or HMI. When the wiring mode is Delta, Uab,
Ubc and Uca corresponds to Phase A, Phase B and Phase C, respectively.
Code Color Code Color Code Color
1 Brown 4 Yellow 7 Gray
2 Red 5 Green 8 Black
3 Orange 6 Blue
Table 5-53 Phase Color
8) If the PMC-592 isn’t equipped with the optional DI3 and DI4, the DI3 and DI4 Debounce registers will be reserved.
9) The value of [PT Primary/PT Secondary] cannot exceed 10000.
10) The Branch CT’s Mains is only meaningful when the Panel Mode is set to Custom . The table below illustrates the details
of the Branch CT’s Mains with 0 and 1 meaning Mains-I and Mains-II, respectively.
Bit Bit 3 Bit 2 Bit 1 Bit 0
Branch Branch D Branch C Branch B Branch A
Table 5-54 Branch CT’s Mains (Reg. # 6047)
11) The table below illustrates the relationship between Tariff and DI status. Only one DI can be set as a Tariff Switch.
Tariff Switch Mode DIx Status Tariff
Disabled None None
DIx
Inactive T1
Active T2
Table 5-55 Tariff Switch Mode
5.8.2 Communications Setup
Register Property Description Format Range/Note/Default*
6240 RW Port 1 unit ID UINT16 1 to 247, 100*
6241 RW Port 1 Baud rate UINT16
0 = 1200, 1 = 2400, 2 = 4800,
3 = 9600, 4 = 19200, 5 = 38400*
6242 RW Port 1 Configuration UINT16
0 = 8N2, 1 = 8O1, 2 = 8E1*
3 = 8N1, 4 = 8O2, 5 = 8E2
6243 RW Port 2 unit ID UINT16 1 to 247, 101*
6244 RW Port 2 Baud rate UINT16
0 = 1200, 1 = 2400, 2 = 4800
3 = 9600, 4 = 19200, 5 = 38400*
6245 RW Port 2 Configuration UINT16
0 = 8N2, 1 = 8O1, 2 = 8E1*
3 = 8N1, 4 = 8O2, 5 = 8E2
6246 RW IP Address(H) UINT16 If the IP Address is 192.168.0.100,
write “0xC0A80064” to this register.
(Default = 192.168.0.100)
6247 RW IP Address(L) UINT16
6248 RW Subnet mask(H) UINT16 If the Subnet Mask is 255.255.255.0,
write “0xFFFFFF00” to this register.
(Default = 255.255.255.0)
6249 RW Subnet mask(L) UINT16
6250 RW Gateway Address(H) UINT16 If the IP Address is 192.168.0.1, write
“0xC0A80201” to this register.
(Default = 192.168.2.1)
6251 RW Gateway Address(L) UINT16
6252 RW SNTP Enable UINT16 0 = Disabled*, 1 = Enabled
6253 RW SNTP Time Sync. Interval 1 UINT16 10 to 1440 (min), 60*
6254 RW SNTP Server IP Address (H) UINT16 If address is 192.168.0.100, write
“0xC0A80064” to this register
(Default = 192.168.0.100)
6255 RW SNTP Server IP Address (L) UINT16
6256 RW SMTP Server IP Address (H) UINT16 If address is 191.0.0.6, write
“0XBF000006” to this register
(Default = 191.0.0.6)
6257 RW SMTP Server IP Address (L) UINT16
6258-6297 RW SMTP Sender Username UINT16X40 See Note (2)
6298-6337 RW SMTP Login Password UINT16X40 See Note (3)
6338-6377 RW SMTP Receiver Email Address UINT16X40 See Note (4)
6378 RW TRAP Event Subscription 5 Bitmap 0* to 31
6379 RW TRAP Event Subscriber IP Address (H) UINT16
0*
6380 RW TRAP Event Subscriber IP Address (L) UINT16