Canon CP660 Service Manual Download Page 30 | Manualshive

Page: 30 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

B.

Points to Note When Handling the Drum Cartridge and the
Toner Cartridges

1) When setting a new toner cartridge (Y/M/C toner cartridge, black toner cartridge) in

the printer unit or if white spots occur on output prints because of uneven toner inside
a cartridge, hold the cartridge horizontal and rotate it slowly up and down (about 45°)
five to six times to even out the toner. (Instruct the user to observe this. In addition,
inform the user that handling a toner cartridge other than the foregoing method can
cause leakage of toner from the developing cylinder.)

2) Remove all cartridges if the printer unit must be moved.

In the case of the drum cartridge, put the special protective cover (MF4-0106-000)
after taking it out of the printer unit, and put it in a protective bag or wrap it in a thick
cloth to prevent exposure to light.

3) Do not place the black toner cartridge near a CRT screen, disk drive, or floppy disks.

The magnetic field it generates can damage the data.

4) Do not expose the drum cartridge to direct sunshine or strong light. Doing so could

affect print images.

5) Do not touch the surface of the photosensitive drum of the drum cartridge.
6) Do not place the cartridge on its side or turned over. Be sure that the label side faces

up.

7) Do not disassemble the cartridges.

CHAPTER 1 GENERAL DESCRIPTION

1-18

Black toner cartridge

Y/M/C toner cartridge

Figure 1-701

Download free service manual at http://printer1.blogspot.com

«
...
28
29
30
31
32
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Brand: Xante Pages: 25

Brand: MakerBot Pages: 48

WORKCENTRE 5755

Brand: Xerox Pages: 356

Brand: Axiohm Pages: 8

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: ICT Pages: 34

WorkCentre 7830

Brand: Xerox Pages: 12

Robojet Disc Autoprinter

Brand: Aleratec Pages: 38

Brand: Xiamen Sojet Electronics Pages: 37

Brand: ION Pages: 32

Brand: MUTOH Pages: 12

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 103

Brand: Oki Pages: 6

Brand: 2connet Pages: 25

Brand: TRENDnet Pages: 9

BIZHUB PRO C6500

Brand: Konica Minolta Pages: 30

bizhub PRO 950 Series

Brand: Konica Minolta Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands