manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

IV. TRANSFER

A.

Outline

The transfer block consists of the intermediate transfer drum, secondary pre-transfer

charging assembly, secondary transfer belt, separation static eliminator, and ITD clean-
ing roller, and serves to transfer the toner image from the photosensitive drum to paper
and to remove residual toner.

The intermediate transfer drum is rotated by the drum motor (M2), and the secondary

transfer belt is rotated by the main motor (M4). When the secondary transfer belt clutch
(CL4) turns on, the secondary transfer belt is forced against the intermediate transfer
drum. When the ITD cleaning roller solenoid (SL1) turns on, on the other hand, the ITD
cleaning roller is forced against the intermediate transfer drum.

Figure 4-401

CHAPTER 4  IMAGE FORMATION SYSTEM

4-18

STRCLD*

CLNRON

M4

M2

CL4

SL1

DC controller PCB

Photosensitive 
drum cartridge

photo-
sensitive 
drum

ITD cleaning 
roller

 ITD cleaning 
roller solenoid

 Intermediate
 transfer drum

Secondary pre-transfer 
charging assembly

Separation 
static 
eliminator

Secondary 
transfer belt

Main motor

Secondary transfer
belt clutch

Drum motor

Maim motor drive signal

Drum motor drive signal

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

DataCard SD160 User Manual preview
SD160
Brand: DataCard Pages: 78
DataCard SP75 Plus Quick Install Manual preview
SP75 Plus
Brand: DataCard Pages: 8
DataCard CR805 User Manual preview
CR805
Brand: DataCard Pages: 136
DataCard CE840 Quick Install Manual preview
CE840
Brand: DataCard Pages: 22
DataCard CD820 Quick Install Manual preview
CD820
Brand: DataCard Pages: 16
DataCard SD260 Installation And User Manual preview
SD260
Brand: DataCard Pages: 216
DataCard CD800 Product Manual preview
CD800
Brand: DataCard Pages: 19
DataCard SP55 Plus Supplementary Manual preview
SP55 Plus
Brand: DataCard Pages: 2
DataCard SP55 Plus Printer Manual preview
SP55 Plus
Brand: DataCard Pages: 30
DataCard RP90 Brochure & Specs preview
RP90
Brand: DataCard Pages: 2
DataCard SP25 Plus Brochure & Specs preview
SP25 Plus
Brand: DataCard Pages: 4
DataCard CE870 Quick Install Manual preview
CE870
Brand: DataCard Pages: 24
DataCard SP25 Plus Printer Manual preview
SP25 Plus
Brand: DataCard Pages: 134
DataCard CE870 User Reference Manual preview
CE870
Brand: DataCard Pages: 13
DataCard ImageCard series Supplementary Manual preview
ImageCard series
Brand: DataCard Pages: 2
DataCard ImageCard series Datasheet preview
ImageCard series
Brand: DataCard Pages: 2
DataCard SD Series Quick Install Manual preview
SD Series
Brand: DataCard Pages: 10
DataCard SD160 Quick Install Manual preview
SD160
Brand: DataCard Pages: 8

Brands by name

Popular brands

Load more brands