Canon CP660 Service Manual Download Page 368 | Manualshive

Page: 368 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

2. SENSOR MONITOR

Sensor monitor mode is for displaying the state of the sensors in the paper path of

the printer unit.

Table 10-603 shows the display position and the display reading of each sensor.

Table 10-603

CHAPTER 10 TROUBLESHOOTING

10-86

Description

Use it to monitor the state of the sensors used
in the printer unit. Turn on the sensor manually;
the results of execution will be indicated on the
control panel.

For ‘xx yy zz’, see Table 10-603.

Remarks

Sub Menu

SENSOR
MONITORING

1. The notation “zz” in the display panel (2nd row) is for checks at the factory, and is

not relevant for servicing work.

2. Each sensor has its own response time, some requiring as much as 5 sec. Be sure

to allow adequate time before making a decision.

3. If multiple sensors are turned on at once, the reading will be the sum of the results

in hexadecimal notation.

4. Execution sensor monitor mode can drive some major parts. To avoid contact and,

therefore, injuries, be sure to remove the intermediate transfer drum, various car-
tridges, and secondary transfer belt assembly before starting service mode.

In view of the work, remove the following for each respective sensor:
• For PS1903 and PS5, remove the fixing assembly.
• For PS11, remove the upper cover assembly.
• For PS1207, remove the cassette 1.
• For PS1208, remove the cassette 2.

Caution

:

Display reading

(hexadecimal)

10

08

04

02

01

08

02

01

Display position

xx

yy

Sensor

Face-down tray delivery sensor (PS11)

Fixing delivery sensor (PS1903)

Separation sensor (PS5)

Pick-up assembly sensor (PS17)

Registration paper sensor (PS1)

Lower cassette paper absent sensor
(PS1207)

Upper cassette paper absent sensor
(PS1208)

Multifeeder tray paper sensor (PS1301)

Download free service manual at http://printer1.blogspot.com

«
...
366
367
368
369
370
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

imageRUNNER ADVANCE C3330 Series

Brand: Canon Pages: 5

imagePROGRAF TA-30

Brand: Canon Pages: 49

Brand: Canon Pages: 210

Color imageCLASS MF8180c

Brand: Canon Pages: 34

Brand: TallyGenicom Pages: 166

Brand: Colorjet Pages: 52

AficioSP C410DN

Brand: Ricoh Pages: 204

Brand: Xerox Pages: 150

ORCABOT XXL PRO2

Brand: PRODIM Pages: 41

Brand: TAKE-A-LABEL Pages: 12

HP Toner Cartridges 6R941

Brand: Xerox Pages: 2

Brand: Rimage Pages: 217

Brand: Lexmark Pages: 2

Brand: DURACARD Pages: 31

Brand: Xerox Pages: 342

Color LaserJet CP3520

Brand: HP Pages: 2

Brand: HP Pages: 15

Brand: HP Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands