Canon CP660 Service Manual Download Page 187 | Manualshive

Page: 187 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

B.

Reversing Operation

When the duplexing command arrives from the DC controller PCB, the duplexing dri-

ver PCB turns on the duplexing flapper solenoid (SL6), operating the duplexing flapper
so that paper will be moved to the duplexing unit.

When the leading edge of paper is detected by the reversal sensor (PS26), the

duplexing driver PCB rotates the duplexing motor (M8) counterclockwise (CCW; Note) to
move the paper to the machine’s reversing assembly.

Then, a specific period of time after the reversal paper sensor (PS26) has detected

the trailing edge of the paper, the duplexing driver PCB switches the rotation of the
duplexing motor (M8) to clockwise direction to switch the paper path so that paper will be
moved along the duplexing lower guide to the feeding roller side of the duplexing unit.

Figure 5-403

CHAPTER 5 PICK-UP/FEEDING SYSTEM

5-25

Note:

If paper is not 11x17, A3, B4, or LGL, the duplexing driver PCB first drives the duplex-
ing motor (M8) and then will switch its rotation to high speed to move the paper to the
reversing assembly.

Reversing roller (CCW)

D

uplexing lower guide

Duplexing upper guide

PS26

PS26

Reversing
assembly

Duplexing unit

Duplexing feeding roller 1

Reversing
roller
releasing
plate

Reversing
roller
releasing
plate

Rear
assembly

Reversing roller (CW)

Duplexing upper guide

Duplexing lower guide

Duplexing unit

Duplexing feeding roller 1

M8

M8

Duplexing motor

Duplexing motor

Download free service manual at http://printer1.blogspot.com

«
...
185
186
187
188
189
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Brand: IBM Pages: 112

DocuPrint C2200

Brand: Xerox Pages: 200

Brand: Xerox Pages: 44

Brand: Printronix Pages: 9

Brand: SEH Pages: 20

ApeosPort-III C7600

Brand: Xerox Pages: 369

Brand: Triumph Adler Pages: 4

Brand: Mitsubishi Pages: 86

ECOSYS M6035cdn

Brand: Kyocera Pages: 31

Brand: Gerber Pages: 163

Brand: Noztek Pages: 8

Brand: RHINO Pages: 21

bizhub pro 1200P

Brand: Konica Minolta Pages: 333

Brand: Kyocera Pages: 28

Brand: POSBank Pages: 9

Brand: Loadrite Pages: 16

Brand: Canon Pages: 229

image runner 2520

Brand: Canon Pages: 630

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands