manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10  TROUBLESHOOTING

10-62

B. After executing test print in service mode, the leading edge of print paper reaches the

secondary transfer belt assembly. Or, the print paper is wrapping around the inter-
mediate transfer drum.

Cause

Secondary
transfer belt
locking/unlock-
ing drive gear

Secondary
transfer belt
locking/unlock-
ing drive cam

Connector
(secondary
transfer belt
locking/unlock-
ing clutch CL4)

Secondary
transfer belt
locking/unlock-
ing clutch
(CL4)

Connector
(drum motor
M2)

Drum motor
(M2)

DC controller
PCB

Step

1

2

3

4

5

6

Yes/No

YES

YES

NO

NO

NO

YES

NO

Action

Replace the worn or
cracked part.

Replace the worn or
cracked part.

Connect the connec-
tors securely.

Replace the secondary
transfer belt
locking/unlocking
clutch.

Connect the connector
securely.

End.

Replace the DC con-
troller PCB?

Checks

Is the drive gear used to transmit
locking/unlocking drive of the sec-
ondary transfer belt worn or
cracked?

Is the drive cam used to transmit
locking/unlocking drive of the sec-
ondary transfer belt worn or
cracked?

Are the connectors J212 on the DC
controller PCB and the relay con-
nector J36 connected securely?

Disconnect the connector J212 of
the secondary transfer
locking/unlocking clutch, and mea-
sure the resistance between the
connectors J212-1 (STRCLD*) and
J212-2 (+24 UH) on the harness
side. Is it about 130 

Ω

?

Is the connector J224 on the DC
controller PCB connected securely?

Replace the drum motor (M2). Is the
problem corrected?

If the cause of the jam is the drum motor, the intermediate transfer drum can lock dur-
ing initial rotation and trigger abnormal noise.

Caution

:

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

EasyThreed Mars Quick Start Manual preview
Mars
Brand: EasyThreed Pages: 15
Felix Storch 3.2 Assembly Manual preview
3.2
Brand: Felix Storch Pages: 41
olympia electronics A-200 Manual preview
A-200
Brand: olympia electronics Pages: 4
Oki T400 Guía De Instalación preview
T400
Brand: Oki Pages: 36
Oki T400 Installation preview
T400
Brand: Oki Pages: 3
Panasonic Panafax UF-9000 Service Manual preview
Panafax UF-9000
Brand: Panasonic Pages: 375
Xerox 4150S - WorkCentre B/W Laser Brochure & Specs preview
4150S - WorkCentre B/W Laser
Brand: Xerox Pages: 4
NEC Pinwriter P6 Specification preview
Pinwriter P6
Brand: NEC Pages: 10
Oce PlotWave 300 User Manual preview
PlotWave 300
Brand: Oce Pages: 340
Muratec MFX-1820 Quick Start Manual preview
MFX-1820
Brand: Muratec Pages: 112
Rapid Shape D30+ Original Operating Instructions preview
D30+
Brand: Rapid Shape Pages: 44
Linux SP 221S Setup Manual preview
SP 221S
Brand: Linux Pages: 8
Oki F0305 User Manual preview
F0305
Brand: Oki Pages: 188
Ricoh SP 311DN Installation Manual preview
SP 311DN
Brand: Ricoh Pages: 2
Intellisystem ThermalTronix TT-1025EX-MIL User Manual preview
ThermalTronix TT-1025EX-MIL
Brand: Intellisystem Pages: 11
ADITIVA 3D ENDER 3 BELT KIT Assembly Manual preview
ENDER 3 BELT KIT
Brand: ADITIVA 3D Pages: 43
Printronix ANSI Printer Programmer'S Reference Manual preview
ANSI Printer
Brand: Printronix Pages: 106
Panasonic DP-CL21 Series Setup Manual preview
DP-CL21 Series
Brand: Panasonic Pages: 32

Brands by name

Popular brands

Load more brands