manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

B.

Locking the Secondary Transfer Belt

The secondary transfer belt assembly is locked to the intermediate transfer drum on

which paper is placed before starting secondary transfer.

Normally, the secondary transfer belt assembly is away from the intermediate trans-

fer drum, and is locked to the holding transfer drum as needed.

The DC controller PCB causes the secondary transfer belt clutch drive signal (STGR-

CLD8) to go ‘0’ as soon as paper reaches the secondary transfer belt assembly, turning
on the secondary transfer belt clutch (CL4), driving the secondary transfer belt cam, and
pushing up the secondary transfer belt assembly.

As a result, print paper is forced against the intermediate transfer drum, and the toner

is transferred for the intermediate transfer drum to the print paper.

When paper moves away and secondary transfer ends, the DC controller CPB turns

off the secondary transfer belt clutch (CL4) to move the secondary transfer belt away
from the intermediate transfer drum.

Figure 4-402

CHAPTER 4  IMAGE FORMATION SYSTEM

4-19

CL4

 Intermediate transfer drum

DC controller PCB

Secondary belt clutch

Secondary transfer belt cam

STRCLD*

Secondary transfer 

belt assembly

Paper

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Canon Pixma MG2400 Series Getting Started Manual preview
Pixma MG2400 Series
Brand: Canon Pages: 2
B3 innovations Pico Manual preview
Pico
Brand: B3 innovations Pages: 12
TallyGenicom 6600 Series Quick Reference Manual preview
6600 Series
Brand: TallyGenicom Pages: 310
TallyGenicom 6600 Series Applications Manual preview
6600 Series
Brand: TallyGenicom Pages: 330
Xerox WorkCentre 5325 Administrator'S Manual preview
WorkCentre 5325
Brand: Xerox Pages: 160
Xerox WorkCentre 5016 Specification preview
WorkCentre 5016
Brand: Xerox Pages: 2
Xerox WorkCentre 490cx Online User'S Manual preview
WorkCentre 490cx
Brand: Xerox Pages: 258
Xerox WorkCentre 4260 Series System Administration Manual preview
WorkCentre 4260 Series
Brand: Xerox Pages: 210
Xerox WorkCentre 3550 Information Manual preview
WorkCentre 3550
Brand: Xerox Pages: 32
Xerox WorkCentre 3315DN System Administrator Manual preview
WorkCentre 3315DN
Brand: Xerox Pages: 191
Xerox WORKCENTER 5222 Reference Manual preview
WORKCENTER 5222
Brand: Xerox Pages: 28
Xerox VersaLink C71 Series User Documentation preview
VersaLink C71 Series
Brand: Xerox Pages: 247
Xerox VersaLink C7000 Installation Manual preview
VersaLink C7000
Brand: Xerox Pages: 2
Xerox VersaLink C505 Quick Use Manual preview
VersaLink C505
Brand: Xerox Pages: 21
Xerox VersaLink B71 Series User Documentation preview
VersaLink B71 Series
Brand: Xerox Pages: 234
Xerox WorkCentre 6505 Brochure preview
WorkCentre 6505
Brand: Xerox Pages: 4
Xerox WorkCentre 6015 Quick Use Manual preview
WorkCentre 6015
Brand: Xerox Pages: 16
Xerox Phaser 7750 Color Manual preview
Phaser 7750
Brand: Xerox Pages: 4

Brands by name

Popular brands

Load more brands