manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

D.

Re-Pickup

The duplexing driver PCB turns on the duplexing feeding clutch (CL5) at the end of

horizontal registration so as to move paper once gain.

About 0.5 sec after the duplexing unit paper sensor (PS24) has detected the leading

edge of paper, the duplexing driver PCB turns of the reversing roller releasing solenoid
(SL7; if the paper is not A4R, LTRR, or A5); about 1.0 sec later, it turns off the duplexing
feeding clutch (CL5). While keeping the paper at re-pickup wait position, the duplexing
driver PCB waits for a re-pickup command from the DC controller PCB.

When the re-pickup command is received from the DC controller PCB, the duplexing

driver PCB controls the speed of the duplexing motor (M8) so that it matches the
machine’s feeding speed; thereafter, it turns on the duplexing feeding clutch (CL5) to
move the paper to the machine’s feeding assembly.

Figure 5-405

CHAPTER 5  PICK-UP/FEEDING SYSTEM

5-28

Reversing roller

Duplexing lower guide

Reversing 

roller 

releasing 

plate

Reversing roller releasing solenoid

Duplexing upper guide

Reversing 

assembly

Duplexing unit

Duplexing feeding roller 1

 Duplexing unit 

paper sensor lever

Duplexing 
feeding roller 2

Duplexing unit paper sensor (PS24)

CL5

SL7

M8

OFF

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Oki PACEMARK 4410 Service Manual preview
PACEMARK 4410
Brand: Oki Pages: 215
quadient DS-200iQ User Manual preview
DS-200iQ
Brand: quadient Pages: 130
Xerox Nuvera 120 EA Customer Information preview
Nuvera 120 EA
Brand: Xerox Pages: 5
Oce VarioLink 3622 User Manual preview
VarioLink 3622
Brand: Oce Pages: 209
QuickLabel Systems QL800 User Manual preview
QL800
Brand: QuickLabel Systems Pages: 122
Lexmark 34A0252 Troubleshooting Manual preview
34A0252
Brand: Lexmark Pages: 9
Xerox VersaLink C405/N User Manual preview
VersaLink C405/N
Brand: Xerox Pages: 256
Cycjet ALT382 Manual preview
ALT382
Brand: Cycjet Pages: 26
Oki PACEMARK 4410 Service Handbook preview
PACEMARK 4410
Brand: Oki Pages: 189
Zebra GX420t Instruction Manual preview
GX420t
Brand: Zebra Pages: 29
Oki C7350n User Manual preview
C7350n
Brand: Oki Pages: 187
Xerox WorkCentre 7830 Specification preview
WorkCentre 7830
Brand: Xerox Pages: 12
Tascam P11/TAS Technical Documentation preview
P11/TAS
Brand: Tascam Pages: 2
Anet A8 Plus User Manual preview
A8 Plus
Brand: Anet Pages: 36
Konica Minolta Screen Truepress Jet520 Series Specifications preview
Screen Truepress Jet520 Series
Brand: Konica Minolta Pages: 4
Ricoh AP204 Operator'S Manual preview
AP204
Brand: Ricoh Pages: 301
Magtek ExpressCard 500 User Manual preview
ExpressCard 500
Brand: Magtek Pages: 49
TEC B-570 SERIES Maintenance Manual preview
B-570 SERIES
Brand: TEC Pages: 92

Brands by name

Popular brands

Load more brands