manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10  TROUBLESHOOTING

10-18

Cause

Connector
(cartridge
motor drive)

Cartridge
motor (M3)

High-voltage
PCB 1

DC controller
PCB

Step

5

6

7

Yes/No

NO

YES

YES

NO

Action

Connect them securely.

Replace the cartridge
motor.

End.

Replace the DC con-
troller PCB.

Checks

Are the connectors J5001 and
J5003 on the high-voltage PCB 1
and the connector J226 on the DC
controller PCB connected securely?

Turn on the reader unit rear power
switch and the control panel power
soft switch. Is the voltage between
the connector J5003-1 (+24 UH) on
the high-voltage PCB 1 and the
nearby GND 24 V?

Replace the high-voltage PCB 1. Is
the problem corrected?

4

The print is solid black/solid color.

Cause

Drum cartridge

High-voltage
PCB 1 (for pri-
mary charging
bias)

Step

1

2

3

Yes/No

YES

YES

YES

NO

Action

Clean the contact. If it
is deformed or dam-
aged, replace the prob-
lem part. Also, check
for a displaced contact.

Replace the drum car-
tridge.

End.

Replace the DC con-
troller PCB.

Checks

Is the contact of the drum cartridge
(for primary charging bias) or the
contact for primary charging of the
printer unit soiled?

Replace the drum cartridge (primary
charging roller). Is the problem cor-
rected?

Replace the high-voltage PCB 1. Is
the problem corrected?

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Datecs EP-60 Programmer'S Manual preview
EP-60
Brand: Datecs Pages: 29
Oki C7550 Reference Manual preview
C7550
Brand: Oki Pages: 45
Xerox WorkCentre Pro 40 Specification preview
WorkCentre Pro 40
Brand: Xerox Pages: 14
Magicard Tango 2e Brochure preview
Tango 2e
Brand: Magicard Pages: 2
Magicard Tango 2e Quick Start Manual preview
Tango 2e
Brand: Magicard Pages: 2
Xerox Phaser 6200N Manual preview
Phaser 6200N
Brand: Xerox Pages: 13
Xerox 6360V_DN Evaluator Manual preview
6360V_DN
Brand: Xerox Pages: 16
Lanier LD1110 Settings Manual preview
LD1110
Brand: Lanier Pages: 298
Xerox 6130N - Phaser Color Laser Printer Instruction Sheet preview
6130N - Phaser Color Laser Printer
Brand: Xerox Pages: 2
Xerox 6130N - Phaser Color Laser Printer Installation Manual preview
6130N - Phaser Color Laser Printer
Brand: Xerox Pages: 2
Samsung CLX-9350ND Service Manual preview
CLX-9350ND
Brand: Samsung Pages: 549
Olivetti FS-529 Service Manual preview
FS-529
Brand: Olivetti Pages: 33
Axis 570 MIO Quick Installation Manual preview
570 MIO
Brand: Axis Pages: 10
Star Micronics Multi-Font NX-2415 User Manual preview
Multi-Font NX-2415
Brand: Star Micronics Pages: 134
Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual preview
Fast T-Jet Blazer Pro
Brand: Screen Print & Inkjet Pages: 138
Kyocera ECOSYS FS-C5350DN Service Manual preview
ECOSYS FS-C5350DN
Brand: Kyocera Pages: 178
E-Pos TEP-220M User Manual preview
TEP-220M
Brand: E-Pos Pages: 21
Canon varioPRINT 6000 TITAN Series Manual preview
varioPRINT 6000 TITAN Series
Brand: Canon Pages: 69

Brands by name

Popular brands

Load more brands