Canon CP660 Service Manual Download Page 107 | Manualshive

Page: 107 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

D.

Monitoring the Waste Toner Case

The toner inside the waste toner case is monitored by the waste toner detecting

assembly mounted to the drum cartridge.

The detecting assembly consists of a light-emitting section and a light-receiving sec-

tion. The light generated by the light-emitting section is directed to the detecting window
of the drum cartridge. It moves through the cartridge when the stirring plate inside moves
toner away from around the detecting widow. The light is then detected by the light-receiv-
ing section through the waste toner case; the DC controller PCB finds out the time to
when waste toner once again covers the detecting window.

When the period during which light is passing through is shorter than a specific value,

the DC controller PCB will identify the fact as a waste toner full warning condition, and
communicates it to the printer board1. It also writes the data to the drum cartridge mem-
ory.

The copier remains capable of making copies after the warning, but the DC controller

PCB starts counting the prints made since the warning has been issued; it will identify a
waste toner full condition when the count reaches a specific value, and will stop the
machine and communicates the fact to the printer board*

1

.

*

1

Reader controller PCB (when making prints with the reader unit installed).

Reference:

COPIER>DISPLAY>SENSOR>W-TONER (indicated on the control panel if the read-
er unit is installed)
0:

not full.

1:

full warning.

Reference:

E013:

stops the machine in response to waste toner case full condition.

E019:

waste toner detecting assembly malfunction.

Figure 4-203

CHAPTER 4 IMAGE FORMATION SYSTEM

4-9

,,,,,,

,,,,,,

,,,,,,

,,,,,,

,,,,,,

Light-emitting

section

Waste toner

Light-receiving section

Detecting

window

Stirring

plate

Toner feeding roller

Photosensitive drum

Waste toner detecting

assembly

Download free service manual at http://printer1.blogspot.com

«
...
105
106
107
108
109
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

imagePROGRAF iPF760

Brand: Canon Pages: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 16

imagePRESS C850

Brand: Canon Pages: 146

imagePRESS C850

Brand: Canon Pages: 63

imagePROGRAF iPF760

Brand: Canon Pages: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 8

imagePROGRAF TX-2000

Brand: Canon Pages: 14

i-SENSYS MF6180dw

Brand: Canon Pages: 1040

imagePROGRAF iPF815

Brand: Canon Pages: 48

imageRUNNER 1025

Brand: Canon Pages: 6

imageRUNNER 2230

Brand: Canon Pages: 6

IMAGEPRESS C7010VPS

Brand: Canon Pages: 388

Brand: Canon Pages: 56

imagePROGRAF iPF8300

Brand: Canon Pages: 24

imagePROGRAF iPF8300

Brand: Canon Pages: 4

imagePROGRAF iPF6350

Brand: Canon Pages: 12

imagePROGRAF iPF6350

Brand: Canon Pages: 2

imageCLASS MF8380Cdw

Brand: Canon Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands