Canon CP660 Service Manual Download Page 264

Page: 264 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

Selecting the Type of Message for the Printer Unit

If you have installed the PS/PCL Board to the printer unit, you must select the type of

message appearing on its control panel.

• EUROPE

for service maintenance

• JAPAN

not used

• UNITED STATES

for user maintenance

• UNKNOWN

not used

• EUROPE2

not used

• JAPAN2

not used

• UNITED STATES2

for service maintenance

The default setting is UNITED STATES (i.e., for user maintenance).
To change the type of message, perform the following:

CHAPTER 8 INSTALLATION

8-14

Work

Turn off the printer unit.

Check to make sure that the jumper head is
fitted to J27 of the PS/PCL Board.

Install the PS/PCL Board to the printer unit.

While holding down the Menu and

key on

the control panel of the printer unit, turn on
the printer unit.

At this time, be sure to hold down the two
keys until the message ‘START SELF-TEST’
appears.

Wait until the printer unit has run self diagno-
sis, and indicates the message ‘VERSION
INFO’

Press the Menu key several times so that the
message ‘CHANGE DEFAULT LOCALE:’
appears.

Press the Enter key.

When ‘DEFAULT LOCALE:’ has appeared,
select the item that indicates the site of instal-
lation using the

key.

(The currently selected item is indicated by
the asterisk * on the last digit.)

Remarks

If the printer unit has started without
displaying the message, turn it off, and
start with step 4.

• EUROPE

for service maintenance

• JAPAN

not used

• UNITED STATES

for user maintenance

• UNKNOWN

not used

• EUROPE2

not used

• JAPAN2

not used

• UNITED STATES2

for service maintenance

The default setting is UNITED STATES
(i.e., for user maintenance).

No.

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660






















































































































































































































































































































































































































Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands

Canon CP660, Service Manual

Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands