Canon CP660 Service Manual Download Page 75 | Manualshive

Page: 75 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

B.

Image Signal Processing

The printer board sends video signals (VDO0 through 7*; C, M, Y, and Bk, each rep-

resenting 8-bit data) and CMD* signals (image mode switching command) to the DC con-
troller PCB. The D-CPU (IC201) on the DC controller PCB is used to generate image
mode switch signals (VDATIN8*; Note) from CMD* signals.

The video signals (DVDO0 through 7*) sent by the printer board *

1

to the DC con-

troller PCB are directed to a RAM (IC205; line memory) and then to a gate array (IC204).

The video signals (DVDO0 through 7*) are subjected to image masking processing

(p. 3-3) in IC204, and are sent to the PWM IC (IC208) as video data signals (VDATO0
through 7). At the same time, the image mode switch signals (VDATIN8*) are moved
through the gate array (IC204), and are sent to the PWM IC (IC208) as PWMF1 signals.

Then, the video data signals (VDATO0 through 7) are turned into PWM demodulation

signals (VDATA*; PWM video data signals) combined with PWMF1 signals (selected
image mode) by the PWM IC (IC208); they are then sent to the laser driver PCB of the
laser scanner as two sets of laser drive signals (BDATA*, BDATA) by way of the LVDS IC
(IC209).

When making full-color copies, the foregoing operations are performed for Y, M, C,

and BK in sequence to form images. When making mono-color copies, on the other hand,
these operations are performed for one of the four colors.

At the end, the laser driver PCB is ready to send the laser drive signals (DATA*; result

of demodulation by the receiver (IC1001) to the laser drive IC (IC1002).

*

1

Reader controller PCB (when making copies with the reader unit installed).

Note:

Switching the Image Mode
The printer unit switches image mode (text or halftone) in response to the image mode
switch command from the reader controller PCB so as to enable the best images in
text and halftone areas.

CHAPTER 3 LASER EXPOSURE SYSTEM

3-5

Download free service manual at http://printer1.blogspot.com

«
...
73
74
75
76
77
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

imagePROGRAF W8400

Brand: Canon Pages: 24

Super G3 FAX Board-T1

Brand: Canon Pages: 16

imagePROGRAF TZ-30000

Brand: Canon Pages: 66

imagePROGRAF W7200

Brand: Canon Pages: 126

imagePROGRAFi iPF840 series

Brand: Canon Pages: 149

Brand: Canon Pages: 166

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 2

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Olympus Pages: 3

BW Remote Operators Software Kit-A1

Brand: Canon Pages: 20

imageRUNNER 2420

Brand: Canon Pages: 30

Brand: Canon Pages: 51

imageCLASS LBP325dn

Brand: Canon Pages: 252

Brand: V-King Pages: 41

Brand: TallyGenicom Pages: 166

Brand: Panasonic Pages: 169

Brand: Oki Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands