manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 8  INSTALLATION

8-21

No.

4

Work

Match the groove in the bottom of the vertical
feed cassette and the left side with the guide
on the printer unit to set the cassette to the
printer unit.

Remarks

Match the triangle markings on the printer 
unit and the triangle markings on the pick-
up cassette; then, place the left side of 
the cassette on the copier's guide.

The vertical feed cassette is designed
for the holder for the cassette 1 only.
Be sure not to force it inside at an
angle (top/bottom, let/right).

Caution

:

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Oki C7300 Replacement Instructions preview
C7300
Brand: Oki Pages: 2
Oki 6150 Setup Manual preview
6150
Brand: Oki Pages: 40
Qilive Q.3622 Instruction Manual preview
Q.3622
Brand: Qilive Pages: 398
Canon imagePROGRAF GP-540 Setup Manual preview
imagePROGRAF GP-540
Brand: Canon Pages: 82
Canon i9100 Series Setup Instructions preview
i9100 Series
Brand: Canon Pages: 2
Canon imageRUNNER C3480 Easy Operation Manual preview
imageRUNNER C3480
Brand: Canon Pages: 92
Oki C931dn Manual Del Usuario preview
C931dn
Brand: Oki Pages: 328
µ-Dimension BST 1200es User Manual preview
BST 1200es
Brand: µ-Dimension Pages: 74
Tektronix Phaser 600 Service Manual preview
Phaser 600
Brand: Tektronix Pages: 286
Ricoh SP 204SFNw Brochure & Specs preview
SP 204SFNw
Brand: Ricoh Pages: 2
Konica Minolta Magicolor 4650DN User Manual preview
Magicolor 4650DN
Brand: Konica Minolta Pages: 260
3nStar PPT205 User Manual preview
PPT205
Brand: 3nStar Pages: 8
Brady BradyPrinter A5500 User Manual preview
BradyPrinter A5500
Brand: Brady Pages: 72
G&G IMAGE L2550DW Series User Manual preview
IMAGE L2550DW Series
Brand: G&G Pages: 147
Pantum M6503 Series User Manual preview
M6503 Series
Brand: Pantum Pages: 155
Tektronix Phaser 220 Reference Manual preview
Phaser 220
Brand: Tektronix Pages: 178
Wasp 4070 ZX Original Instructions Manual preview
4070 ZX
Brand: Wasp Pages: 82
Ricoh PRSPC342DN1 User Manual preview
PRSPC342DN1
Brand: Ricoh Pages: 120

Brands by name

Popular brands

Load more brands