manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

V. DETECTING JAMS

A.

Detecting Jams in the Printer Unit

The printer unit is equipped with the following paper sensors to check the pres-

ence/absence of paper and to find out whether paper is moving normally inside it:

• Registration paper sensor (PS1)
• Pick-up assembly paper sensor (PS17)
• Separation sensor (PS5)
• Face-down tray delivery sensor (PS11)
• Transparency sensor 1/2 (PS1801/PS1802)
• Fixing delivery sensor (PS1903)
A jam is identified in relation to the presence/absence of paper at a specific sensor at

such times as programmed in the microprocessor (CPU) in advance.

When the microprocessor identifies a jam, it stops the ongoing printing operation and

communicates the fact to the printer board*

1

.

*

1

Reader controller PCB (when making prints with the reader unit installed).

Figure 5-501

CHAPTER 5  PICK-UP/FEEDING SYSTEM

5-29

Face-down 
delivery 
roller

Face-down tray

Intermediate 

transfer drum

Upper 

fixing roller

Lower 

fixing roller

Multifeeder 

pick-up roller

Pick-up roller

Registration roller

Cassette 1

Face-up tray

Face-up 

delivery roller

Feeding roller 2

Pick-up roller

Cassette 2

Secondary 

transfer belt

PS11

Face-down tray 

delivery sensor

PS19

Fixing delivery 

sensor

PS1

Registration paper 

sensor

PS17

Pick-up 

assembly 

paper sensor

PS5

Separation 

sensor

Transparency sensor

PS1802

Transparency sensor

PS1801

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Oki 86 Specifications preview
86
Brand: Oki Pages: 4
TallyGenicom LA550N User Manual preview
LA550N
Brand: TallyGenicom Pages: 145
Tally T2265 SprintPro Reference Manual preview
T2265 SprintPro
Brand: Tally Pages: 217
TallyGenicom 2248 Product Manual preview
2248
Brand: TallyGenicom Pages: 12
Xerox Nuvera 120 EA Customer Information preview
Nuvera 120 EA
Brand: Xerox Pages: 5
WIEDENBACH Komax ims 295 BC Operating Manual preview
Komax ims 295 BC
Brand: WIEDENBACH Pages: 52
Oki MPS4700mb Safety Information Manual preview
MPS4700mb
Brand: Oki Pages: 40
Oki C9000 Series User Manual preview
C9000 Series
Brand: Oki Pages: 204
Xerox AltaLink C81 Series User Manual preview
AltaLink C81 Series
Brand: Xerox Pages: 412
Oce cm5520 User Manual preview
cm5520
Brand: Oce Pages: 366
Roland SJ-1045EX User Manual preview
SJ-1045EX
Brand: Roland Pages: 116
Xerox WorkCentre 5687 Series Service Manual preview
WorkCentre 5687 Series
Brand: Xerox Pages: 2320
Xerox VersaaLink B600 User Manual preview
VersaaLink B600
Brand: Xerox Pages: 170
Epson EPL-5500W Service Manual preview
EPL-5500W
Brand: Epson Pages: 105
Epson EPL-5700 Service Manual preview
EPL-5700
Brand: Epson Pages: 128
Epson EPL-5500 Service Manual preview
EPL-5500
Brand: Epson Pages: 145
Epson EPL N2700 Service Manual preview
EPL N2700
Brand: Epson Pages: 200
Epson EPL-2020 Setup preview
EPL-2020
Brand: Epson Pages: 2

Brands by name

Popular brands

Load more brands