Canon CP660 Service Manual Download Page 178 | Manualshive

Page: 178 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

B.

Pick-Up from the Multifeeder Tray

1. Operation

The presence/absence of paper on the multifeeder tray is checked by the multifeed-

er tray paper sensor (PS1301).

In response to the PRNT* signal, the DC controller PCB starts the main motor (M4).

At the same time, it turns on the holding plate solenoid (SL4) to free the holding plate (so
that it may move up), causing the pick-up roller to come into contact with the stack of
paper.

The up/down movement of the holding plate is checked by the holding plate sensor

(PS1302). If the holding plate is up during the wait period, the holding plate solenoid
(SL4) is turned on to bring down the holding plate.

Thereafter, the multifeeder pick-up clutch (CL3) is turned on so that the drive of the

main motor (M4) is transmitted to the multifeeder tray pick-up roller.

The stack of paper butted against the multifeeder tray pick-up roller by the holding

plate gives up one sheet in response to the rotation of the pick-up roller. After the extra
sheet, if any, has been removed by the work of the separation pad, the paper is moved
inside the printer unit. The operations that follow are the same as in cassette pick-up;
however, the holding plate solenoid (SL4) is additionally turned on immediately after the
registration roller starts to rotate to move down the holding plate.

The multifeeder tray paper width sensor (PS1701) is mounted inside the feeder tray,

detecting the width of paper in relation to the slide resistor operating in conjunction with
the size guide plate.

The DC controller PCB detects the width of paper, if any on the multifeeder tray; if the

paper is of a width different from the width specified by the printer board*

1

, it will identify

a paper size mismatch, and communicate the fact to the printer board1 and, at the same
time, issues a message on the printer control panel to warn the user.

*

1

Reader control PCB (when making prints with the reader unit installed).

CHAPTER 5 PICK-UP/FEEDING SYSTEM

5-16

Download free service manual at http://printer1.blogspot.com

«
...
176
177
178
179
180
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Brand: Oki Pages: 16

Brand: DataCard Pages: 8

Brand: DataCard Pages: 8

Brand: DataCard Pages: 3

Brand: Unimark Pages: 38

Brand: Oki Pages: 94

Brand: MAC TOOLS Pages: 2

LaserPro StellarMark IFII Series

Brand: GCC Technologies Pages: 111

Brand: Lexmark Pages: 729

Brand: SPRT Pages: 15

Brand: IOGear Pages: 44

Brand: Konica Minolta Pages: 102

Aficio SP 320 Series

Brand: Ricoh Pages: 272

Brand: Oki Pages: 56

Brand: Pantum Pages: 95

Stylus Color C70

Brand: Epson Pages: 2

Stylus Color C80

Brand: Epson Pages: 11

Stylus Color C60

Brand: Epson Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands