Canon CP660 Service Manual Download Page 15

Page: 15 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 1 GENERAL DESCRIPTION

1-3

Wait time

5 min or less

First print time

See Table 1-201.

Printing speed

See Table 1-202.

Cassette

Universal cassette:

about 500 sheets of 80 g/m

R cassette (accessory): about 500 sheets of 80 g/m

Multifeeder tray

about 10 mm in height (about 100 sheets of 80 g/m

)

Duplexing unit

Through-path (accessory)

Delivery tray

Face-down: about 300 sheets (80 g/m

paper), w/ limit sensor

Face-up: about 100 sheets (80 g/m

paper)

Print size

Cassette 1

Universal cassette: LGL, B4, LTR, A4
Special cassette (accessory): LTRR, A4R, B5R, A5R

Cassette 2

Universal cassette: 11

17, A3, LGL, B4, LTR, A4

Multifeeder

Envelope, A3 (11

17) to A5 (if B5 and A5, horizontal only);

18.5

Print paper

Cassette

Plain paper (60 to 105 g/m

), colored paper, recycled paper

Multifeeder

Plain paper (60 to 105 g/m

), transparency (special), thick

paper (106 to 135 g/m

), label sheet (special), envelope, col-

ored paper, recycled paper

Double-sided

Duplexing unit (if installed) : A3 to B5R plain paper (60 to

printing

105 g/m

)

Image margin

Single-sided

Double-sided

Leading edge: 5.0 ±2.0 mm

Trailing edge: 5.0 ±2.0 mm

Left/right:

5.0 ±2.0 mm

Left/right:

5.0 ±2.0 mm

Non-image width

Single-sided

Double-sided

Leading edge: 5.0 ±2.0 mm

Trailing edge: 5.0 ±2.0 mm

Left/right:

5.0 ±2.0 mm

Left/right:

5.0 ±2.0 mm

Resolution

Main scanning

600 dpi (dots per inch)

direction

Sub scanning

600 lpi (lines per inch)

direction

3. Functions

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660






















































































































































































































































































































































































































Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands

Canon CP660, Service Manual

Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands