manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

I. OUTLINE

A.

Outline

When the PRNT* signal arrives from the printer board*

1

and the scanner motor

becomes ready, the DC controller PCB starts printing operation.

In the case of pick-up from the cassette, paper is fed into the printer unit by the pick-

up roller and is moved by the feeding roller; in the case of pick-up from the multifeeder,
on the other hand, the multifeeder pick-up roller feeds paper into the printer unit.

The orientation of the paper is corrected by the registration roller so that it will not

move askew; the paper is then stopped and kept in wait. Then, the paper is started once
again so that its leading edge and the leading edge of the image on the intermediate
transfer drum will match; the paper is further moved through the transfer, separation, and
fixing/delivery assemblies all the way to the face-down tray or the face-up tray.

*

1 

Reader controller PCB (when making prints with the reader unit installed).

Figure 5-101

CHAPTER 5  PICK-UP/FEEDING SYSTEM

5-1

Face-down delivery roller

Face-down tray

Intermediate transfer 

drum

Upper fixing 

roller

Lower fixing roller

Multifeeder pick-up 

roller

Pick-up roller

Registration 

roller

Cassette 1

Separation roller

Feeding 
rollers 1

Face-up tray

Face-up delivery 

roller

Feeding roller 2

Separation roller

Pick-up roller

Cassette 2

Secondary 

transfer 

belt

Photosensitive drum

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Canon i 320 Simplified Manual preview
i 320
Brand: Canon Pages: 18
Canon G1020 Series Getting Started preview
G1020 Series
Brand: Canon Pages: 16
Canon CX-G2400 Getting Started Manual preview
CX-G2400
Brand: Canon Pages: 39
Canon i455 Series Setup Instructions preview
i455 Series
Brand: Canon Pages: 2
Canon i455 Series Quick Start Manual preview
i455 Series
Brand: Canon Pages: 73
Canon i70 Series Quick Start Manual preview
i70 Series
Brand: Canon Pages: 29
Canon i550 Parts Catalog preview
i550
Brand: Canon Pages: 16
Canon i475D Series Printing Manual preview
i475D Series
Brand: Canon Pages: 44
Canon G3410 Getting Started preview
G3410
Brand: Canon Pages: 60
Olympus P 400 Easy Printing Manual preview
P 400
Brand: Olympus Pages: 236
Canon I450 - i 450 Color Inkjet Printer Simplified Manual preview
I450 - i 450 Color Inkjet Printer
Brand: Canon Pages: 13
Oki C7300 Replacement Instructions preview
C7300
Brand: Oki Pages: 2
Olivetti d-COLOR MF254 Replacement Procedure preview
d-COLOR MF254
Brand: Olivetti Pages: 2
Olivetti d-COLOR MF3300 Operations preview
d-COLOR MF3300
Brand: Olivetti Pages: 109
Olivetti d-COLOR MF3300 User Manual preview
d-COLOR MF3300
Brand: Olivetti Pages: 111
Olivetti d-Color MF1600 Setup Manual preview
d-Color MF1600
Brand: Olivetti Pages: 8
Xerox PHASER 6121MFP Service Manual preview
PHASER 6121MFP
Brand: Xerox Pages: 532
Xerox Phaser 6120 User Manual preview
Phaser 6120
Brand: Xerox Pages: 174

Brands by name

Popular brands

Load more brands