Canon CP660 Service Manual Download Page 325

Page: 325 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10 TROUBLESHOOTING

10-43

Cause

Drum cartridge

Drum cartridge
switching lever

Drum cartridge
switching guide

Connector
(memory inside
the drum car-
tridge)

Memory (inside
the drum car-
tridge)

Step

Yes/No

YES

Action

Set the cartridge cor-
rectly, and turn off and
then on the printer unit.

Set the lever to the cor-
rect position. If it is
cracked, replace it.

Replace the drum car-
tridge.

Connect the connec-
tors securely.

End.

Replace the DC con-
troller PCB.

Checks

Is the drum cartridge set in the print-
er unit correctly?

Check the drum cartridge switching
lever on the printer side. Is it dis-
placed or cracked?

Is the drum cartridge switching
guide deformed?

Are the connector J209 on the DC
controller PCB and relay connectors
J47 and J48 connected securely?

Replace the drum cartridge. Is the
problem corrected?

23 E810

Cause

Fixing assem-
bly

Connector (fix-
ing assembly)

Connector (DC
controller PCB)

Step

Yes/No

YES

Action

Set the fixing assembly
properly, and turn off
and then on the power.

Connect the connector
properly.

Connect the connector.

Replace the DC con-
troller PCB.

Checks

Is the fixing assembly set in the
printer unit properly?

Is the connector J26 of the fixing
assembly connected securely?

Is the connector J222 on the DC
controller PCB connected securely?

25 E813

Cause

Intermediate
transfer drum
(ITD), Density
sensor

Step

Yes/No

YES

Action

Set the drum properly,
and turn off and then
on the power.

See “8.E020”.

Checks

Is the intermediate transfer drum
(ITD) set in the printer unit properly?

24 E812

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660






















































































































































































































































































































































































































Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands

Canon CP660, Service Manual

Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands