manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

• During standby, the temperature is controlled to 165°C.
• During printing, the temperature is varied to suit the selected fixing mode (Note).

Reference:

The voltage is highest in the reader unit while the scanner is moved in reverse during
printing operation with the reader unit installed. As such, the fixing heater is turned off.

B.

Preventing Rush Current

The printer unit uses two heaters, and rush current would be appreciative if both

heaters were turned on at the same time.

In the light of this, the printer unit uses the expansion I/O (IC203) at time of power-on

to generate the rush current prevention drive signal (FXUONS) for the upper fixing heater
and the rush current prevention drive signal (FXLONS) for the lower fixing heater to turn
on the sub drive circuit for a specific period of time to suppress the current applied to the
heaters.

CHAPTER 6  FIXING SYSTEM

6-3

Note:

Fixing Mode
The printer unit sets the target temperature for the upper/lower fixing roller as follows
according to the mode communicated by the printer board*

1

:

Table 6-201

*

1

Reader controller PCB (when making prints with the reader unit installed).

Full-color

Mono-color

Plain paper

mode

180°C

180°C

Transpar-

ency mode

175°C

175°C

Thick paper

mode

175°C

175°C

Envelope

mode

185°C

185°C

Special fixing

mode

180°C

180°C

Target temperature

Color mode

Fixing mode

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Canon imageCLASS Mf6160dw Getting Started Manual preview
imageCLASS Mf6160dw
Brand: Canon Pages: 64
Canon imageCLASS MF6500 Series Advanced Manual preview
imageCLASS MF6500 Series
Brand: Canon Pages: 132
Canon imageCLASS MF5550 Software Manual preview
imageCLASS MF5550
Brand: Canon Pages: 120
Canon imageCLASS MF5630 User Manual preview
imageCLASS MF5630
Brand: Canon Pages: 85
Canon imageCLASS MF5550 Basic Manual preview
imageCLASS MF5550
Brand: Canon Pages: 136
Canon IMAGECLASS MF7400 Starter Manual preview
IMAGECLASS MF7400
Brand: Canon Pages: 40
Canon imageCLASS MF5850dn Settings Manual preview
imageCLASS MF5850dn
Brand: Canon Pages: 34
Canon imageCLASS MF6500 Series Starter Manual preview
imageCLASS MF6500 Series
Brand: Canon Pages: 16
Canon imageCLASS MF6540 Software Manual preview
imageCLASS MF6540
Brand: Canon Pages: 82
Canon imageCLASS MF5550 Facsimile Manual preview
imageCLASS MF5550
Brand: Canon Pages: 99
Canon imageCLASS MF5630 Quick Reference Manual preview
imageCLASS MF5630
Brand: Canon Pages: 24
Canon imageCLASS MF5770 Setup Sheet preview
imageCLASS MF5770
Brand: Canon Pages: 2
Canon imagePRESS C7000VP Series Customer Expectation Document preview
imagePRESS C7000VP Series
Brand: Canon Pages: 48
Canon imageClass MF5650 Parts Catalog preview
imageClass MF5650
Brand: Canon Pages: 40
Canon imageCLASS MF5770 User Manual preview
imageCLASS MF5770
Brand: Canon Pages: 8
Canon imageCLASS MF4880dw Starter Manual preview
imageCLASS MF4880dw
Brand: Canon Pages: 36
Canon imageCLASS MF4890dw Basic Operation Manual preview
imageCLASS MF4890dw
Brand: Canon Pages: 116
Canon ImageCLASS MF4690 Reference Manual preview
ImageCLASS MF4690
Brand: Canon Pages: 387

Brands by name

Popular brands

Load more brands