Canon CP660 Service Manual Download Page 36

Page: 36 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

Step 2 (primary charging)

In preparation for laser beam exposure, the surface of the photosensitive drum is

charged to a uniform negative potential. The machine’s primary charging consists in
directly charging the photosensitive drum.

The primary charging roller is given a AC bias, in addition to the DC bias, to ensure

that the potential on the surface of the photosensitive drum will be uniform.

Step 3 (laser beam exposure)

When a laser beam is directed to the photosensitive drum, the charges in its light area

become neutralized, turning the area into a latent static image.

CHAPTER 1 GENERAL DESCRIPTION

1-24

Primary charging roller

AC bias

DC bias

Photosensitive drum

Figure 1-805

Laser beam

Dark area

Light area

Figure 1-806

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660






















































































































































































































































































































































































































Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands

Canon CP660, Service Manual

Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands