Canon CP660 Service Manual Download Page 265 | Manualshive

Page: 265 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

■

Making Sure of the Change
• You can start the printer unit and print a start page. (Check the name of the prod-

uct, which differs according to the site of installation.)

• While the machine is in ready state, remove the photosensitive drum unit, and close

the front door. If ‘INSTALL DRUM CARTRIDGE’ appears on the control panel of the
printer unit, the machine is set for user maintenance; if ‘SERVICE CALL E810’
appears, it is set for service maintenance.

CHAPTER 8 INSTALLATION

8-15

Work

After making the selection, press the Enter
key.

The message ‘LOCALE STORED’ will appear
and remain for about 1 sec, to be replaced by
the message ‘CHANGE DEFAULT LOCALE:’.

Turn off the printer unit, and remove the
PS/PCL Board from the printer unit.

Detach the jumper head J27 of the PS/PCL
Board, and install the PS/PCL Board to the
printer unit once again.

Turn on the printer unit.

Remarks

Be sure to detach the jumper head
from J27, and store away the head for
future use.

No.

9

10

11

12

• If the jumper head is not fitted to J27, the menu for ‘CHANGE DEFAULT LOCALE:’

will not appear during the above procedure.

• Do not change any items except ‘CHANGE DEFAULT LOCALE:’.

Caution

:

Download free service manual at http://printer1.blogspot.com

«
...
263
264
265
266
267
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Brand: ABLE Pages: 26

Brand: Lanier Pages: 6

Brand: BCS Pages: 151

Brand: SEH Pages: 5

5550B - Phaser B/W Laser Printer

Brand: Xerox Pages: 117

WorkCentre 3345

Brand: Xerox Pages: 18

Brand: U-Line Pages: 18

Brand: Konica Minolta Pages: 8

Brand: Oki Pages: 18

invitrogen EVOS FL

Brand: Thermo Scientific Pages: 6

Brand: EBS Pages: 20

Brand: Olivetti Pages: 97

MAC TECHNICAL REFERANCE C7350

Brand: Oki Pages: 95

Brand: Sam4s Pages: 24

Brand: Epson Pages: 157

Brand: MINOLTA-QMS Pages: 48

Brand: Sharp Pages: 40

Brand: Sharp Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands