Canon CP660 Service Manual Download Page 299

Page: 299 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10 TROUBLESHOOTING

10-17

The print is too dark.

Cause

Density sensor

Grounding wire
contact (drum
cartridge)

Contact (drum
cartridge; for
primary charg-
ing bias)

High-voltage
PCB 1 (primary
charging bias
output)

Step

Yes/No

YES

Action

Clean the lens with a
special brush.

Clean the contact. If it
is deformed or dam-
aged, replace the prob-
lem part. Also, check
for a displaced contact.

End.

Replace the DC con-
troller PCB.

Checks

Is the lens of the density sensor
soiled?

Is the contact of the grounding wire
of the drum cartridge or the contact
of the drum grounding wire for the
printer unit soiled?

Is the contact of the drum cartridge
(for primary charging bias) or the
contact for primary charging of the
printer unit soiled?

Replace the high-voltage PCB 1. Is
the problem corrected?

The print is blank.

Cause

Laser shutter

High-voltage
PCB 1

High-voltage
PCB 1 (no
color/black
developing bias
output)

Step

Yes/No

YES

Action

Replace the front cover
or the right cover.

Replace the problem
part.

Connect them securely.

Replace the high-volt-
age PCB 1.

Checks

Is the boss for opening/closing the
laser shutter on the front cover or
the right cover of the printer unit
damaged?

Does the laser shutter arm and the
laser shutter move smoothly?

Are the connectors J5001 and J226
on the high-voltage PCB 1 connect-
ed securely?

Replace the high-voltage PCB 1. Is
the problem corrected?

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660






















































































































































































































































































































































































































Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands

Canon CP660, Service Manual

Search results

Summary of Contents for CP660

Reviews:

Related manuals for CP660

Brands by name

Popular brands