manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 4  IMAGE FORMATION SYSTEM

4-46

3) While holding the left and right levers

of the intermediate transfer drum, pull
the drum straight; when it stops,
remove it as if to lift it at an angle.

Figure 4-824

Note:

The intermediate transfer drum is
heaviest at the rear. Remove it as if to
lift its rear.

2. Mounting a New Immediate

Transfer Drum

1) Remove the protective sheet from the

new intermediate transfer drum as
shown.

Figure 4-825

Note:

Take care not to scratch the surface of
the intermediate transfer drum. Avoid
touching it.

2) Mount the intermediate transfer drum

by reversing the steps used to remove
it.

Figure 4-826

3) Shift back the bottom releasing lever

of the front cover to close the cover.

Note:

The intermediate transfer drum must
be mounted correctly to set the bottom
releasing lever.

4) Close the right cover and the front

cover.

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Canon image Prograf iPF785 Series Basic Manual preview
image Prograf iPF785 Series
Brand: Canon Pages: 136
GBC A1 Operation & Instruction Manual preview
A1
Brand: GBC Pages: 110
Xerox M Series Initial Setup Card preview
M Series
Brand: Xerox Pages: 2
Oki C5800 Brochure & Specs preview
C5800
Brand: Oki Pages: 6
Oki C7300 Référence Matérielle preview
C7300
Brand: Oki Pages: 44
Oki C7500 Enhancements Manual preview
C7500
Brand: Oki Pages: 13
Oki C7300 Software Installation Manual preview
C7300
Brand: Oki Pages: 20
Oki C7300 Specifications preview
C7300
Brand: Oki Pages: 2
Oki C5300 Setup Manual preview
C5300
Brand: Oki Pages: 28
Xerox 4050 Operator'S Manual preview
4050
Brand: Xerox Pages: 168
Xerox 4050 Reference Manual preview
4050
Brand: Xerox Pages: 36
Xerox 4050 Installation Planning preview
4050
Brand: Xerox Pages: 64
Xerox 4050 Maintenance Manual preview
4050
Brand: Xerox Pages: 54
Xerox 4050 Quick Reference Card preview
4050
Brand: Xerox Pages: 2
Xerox 4050 Message Manual preview
4050
Brand: Xerox Pages: 115
TallyGenicom LA550N User Manual preview
LA550N
Brand: TallyGenicom Pages: 145
Tally T2265 SprintPro Reference Manual preview
T2265 SprintPro
Brand: Tally Pages: 217
TallyGenicom 2248 Product Manual preview
2248
Brand: TallyGenicom Pages: 12

Brands by name

Popular brands

Load more brands