manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10  TROUBLESHOOTING

10-15

1

The print is too light.

Cause

Black toner
cartridge

High-voltage
PCB 1 (inade-
quate black
developing bias
output)

Secondary pre-
transfer charg-
ing assembly

Intermediate
transfer drum
unit

High-voltage
PCB 2 (inade-
quate pre-
transfer charg-
ing bias output)

Step

1

2

3

4

5

6

Yes/No

YES

YES

NO

YES

YES

NO

YES

Action

If the problem is black
only, go to step 2.
If the problem is three
colors, go to step 7.
If the problem is all four
colors, go to step 9.
If the problem is one
color, go to step 7.

Clean the contact. If it
is deformed, replace
the problem part. Also,
check for a displaced
contact.

Replace the high-volt-
age PCB 1.

Replace the secondary
pre-transfer charging
assembly.

Clean the contact. If it
is soiled or damaged,
replace the problem
part. Also, check for a
displaced contact.

Replace the DC con-
troller PCB.

End.

Checks

Make a test print in service mode
(TEST>PG>TYPE=14), and find the
color that is light on the print.
Is the color on the test print?

Is the contact of the black toner car-
tridge (for black developing bias) or
the contact for black developing bias
of the printer unit soiled?

Open the front cover while black
toner is being developed on the 
photosensitive drum (about 30 sec
after the start of test printing), and
take out the black toner cartridge.
Then, take out the black toner car-
tridge, and check the toner image
on the photosensitive drum. Is the
black toner image fully developed on
the surface of the photosensitive
drum?

Is the charging wire of the sec-
ondary pre-transfer charging assem-
bly inside the intermediate transfer
drum unit broken?

Is the contact of the intermediate
transfer drum unit (for secondary
pre-transfer charging bias) or the
contact for the secondary pre-trans-
fer charging bias of the printer unit
soiled?

Replace the high-voltage PCB. Is
the problem corrected?

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Magicard Prima Brochure preview
Prima
Brand: Magicard Pages: 6
Lanier 5722 Datasheet preview
5722
Brand: Lanier Pages: 3
quadient DS-200iQ User Manual preview
DS-200iQ
Brand: quadient Pages: 130
Samsung Xpress M2020W User Manual preview
Xpress M2020W
Brand: Samsung Pages: 199
Pantum M9106 Series User Manual preview
M9106 Series
Brand: Pantum Pages: 164
Xerox DocuPrint 4850 NPS Configuration Manual preview
DocuPrint 4850 NPS
Brand: Xerox Pages: 276
Oki C7500n Maintenance Manual preview
C7500n
Brand: Oki Pages: 192
StarTech.com PM1115UW Setup Manual preview
PM1115UW
Brand: StarTech.com Pages: 13
Oki OkiPos 407II Installation Manual preview
OkiPos 407II
Brand: Oki Pages: 8
MIMAKI UJF-3042HG Safety Precautions preview
UJF-3042HG
Brand: MIMAKI Pages: 20
Printekmobile MLP-35 Quick Start Manual preview
MLP-35
Brand: Printekmobile Pages: 2
Pantum P2800DW Series User Manual preview
P2800DW Series
Brand: Pantum Pages: 111
Lexmark MX71 series Service Manual preview
MX71 series
Brand: Lexmark Pages: 807
Xerox DocuPrint 3055 User Manual preview
DocuPrint 3055
Brand: Xerox Pages: 240
SATO CLe RFID Smart Specifications preview
CLe RFID Smart
Brand: SATO Pages: 2
Xerox Phaser6121MFP Quick Use Manual preview
Phaser6121MFP
Brand: Xerox Pages: 16
Xerox Nuvera 120 EA Features Manual preview
Nuvera 120 EA
Brand: Xerox Pages: 34
Riso comcolor gd series Safety Information Manual preview
comcolor gd series
Brand: Riso Pages: 34

Brands by name

Popular brands

Load more brands