manualshive.com logo in svg

Canon CP660, Service Manual

The Canon CP660 Service Manual is a comprehensive guide for troubleshooting and repairing this exceptional product. Easily accessible on manualshive.com, users can download this manual for free, allowing them to effectively diagnose and resolve any issues with their Canon CP660, ensuring optimal performance and longevity.

Share
Download
background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10  TROUBLESHOOTING

10-60

Cause

Cassette pick-
up roller, feed-
ing roller 1

Drive gear

Pick-up paper
sensor (PS17)

Pick-up paper
sensor (PS17)

Connector
(pick-up motor
(M5) drive)

Pick-up motor
(M5)

Feeding roller
2

Connector
(feeding clutch
CL2 drive sup-
ply line)

Feeding clutch
(CL2)

Pick-up PCB

DC controller
PCB

Step

1

2

3

4

5

6

7

8

9

10

Yes/No

YES

YES

YES

YES

NO

YES

YES

NO

NO

YES

NO

Action

Replace the parts. Be
sure to replace both
separation roller and
feeding roller 1 at the
same time.

Replace the dam-
aged/worn part.
Position the spring cor-
rectly.

Replace the dam-
aged/worn part.
Position the spring cor-
rectly.

Replace the sensor.

Connect the connec-
tors securely.

Replace the motor.

If worn or deformed,
replace the roller. If
soiled, clean it.

Connect the connector.

Replace the feeding
clutch.

Replace the pick-up
PCB.

Replace the DC con-
troller PCB.

Checks

Is the cassette pick-up roller or the
feeding roller 1 worn/deformed?

Remove the pick-up assembly, and
check the drive gears and springs. Is
there any damaged/worn part? Is
any spring displaced?

Is the pick-up paper sensor lever or
spring damaged/deformed?
Are they positioned correctly?

Replace the pick-up paper sensor. Is
the problem corrected?

Are the connectors J210 on the DC
controller PCB and connectors
J1201 and J1202 on the pick-up
PCB connected securely?

Replace the pick-up motor. Is the
problem corrected?

Is the feeding roller 2 worn,
deformed, or soiled?

Is the connector J1204 of the feed-
ing clutch connected securely?

Disconnect the connector J1204 of
the feeding clutch, and measure the
resistance between the connectors
J1204-2 (+24 UH) and J1204-1
(FEDCLD*) on the harness side. Is it
about 210 

Ω

?

Replace the pick-up PCB. Is the
problem corrected?

2

Cassette Pick-Up Assembly

Download free service manual at http://printer1.blogspot.com

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Radio Shack TRS-80 Operation Manual preview
TRS-80
Brand: Radio Shack Pages: 57
Oki C931dn Manuel D'Utilisation preview
C931dn
Brand: Oki Pages: 320
NEC SuperScript 610 User Manual preview
SuperScript 610
Brand: NEC Pages: 105
Ravas PR-INT-MX-RAVAS-ABLE Manual preview
PR-INT-MX-RAVAS-ABLE
Brand: Ravas Pages: 26
Lexmark X642 Clearing Jams Manual preview
X642
Brand: Lexmark Pages: 4
Oki MB451wMFP User Manual preview
MB451wMFP
Brand: Oki Pages: 198
SEWOO LK-T200 User Manual preview
LK-T200
Brand: SEWOO Pages: 13
Oki C7500 V2 Network Manual preview
C7500 V2
Brand: Oki Pages: 107
Anet A8 Plus User Manual preview
A8 Plus
Brand: Anet Pages: 36
Konica Minolta Screen Truepress Jet520 Series Specifications preview
Screen Truepress Jet520 Series
Brand: Konica Minolta Pages: 4
Ascend Zebra GK420d Field Troubleshooting Manual preview
Zebra GK420d
Brand: Ascend Pages: 6
Oki ML690 Manual Do Usuário preview
ML690
Brand: Oki Pages: 110
TRENDnet TE100-PS3 Administrator User Manual preview
TE100-PS3
Brand: TRENDnet Pages: 135
Oce CS655 User Manual preview
CS655
Brand: Oce Pages: 495
GALLERY 1390R User Manual preview
1390R
Brand: GALLERY Pages: 10
Canon PIXMA E300 series Getting Started preview
PIXMA E300 series
Brand: Canon Pages: 28
Canon MultiPASS F60 Basic Manual preview
MultiPASS F60
Brand: Canon Pages: 115
Canon MF754Cdw Important Safety Instructions Manual preview
MF754Cdw
Brand: Canon Pages: 124

Brands by name

Popular brands

Load more brands