Canon CP660 Service Manual Download Page 282 | Manualshive

Page: 282 / 407

background image

COPYRIGHT © 1999 CANON INC.

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

Guide to Tables

The tables used in this Service Handbook have been prepared from flow charts; study

the sample table below.

AC power is absent.

■

To find the cause (faulty part) for a single problem, see the items under “Cause.” For

“AC power is absent,” the cause may be the power plug, covers, or power source.

■

To find checks to make or actions to take for a single problem, make checks in the

order given, answer the question Yes or No, and take the action given; move onto the
next step as necessary.

■

Checks on the voltage using a tester call for special note; the description “Check the
voltage between J 109-1 (+) and J 109 (-) on the DC controller PCB” means that the
positive probe of the tester should be connected to J 109-1 (+) and the negative probe,
to J 109-2 (-).

Cause

Power plug

Covers

Power source

Step

1

2

3

4

Yes/No

NO

NO

NO

YES

Action

Connect the plug.

Close the door and/or
cover properly.

The problem is not of
the copying machine;
advise the user.

Check step 6) and
onward.

Check

Is the power plug connected to the
outlet?

Are the front door and/or delivery
cover closed properly?

Is the rated voltage (100 VAC) pre-
sent at the outlet?

Is the rated voltage present between
J 1-1 and J 1-2?

YES

YES

YES

NO

Result

Action

Connect the
piug.

The problem is
not of the copy-
ing machine;
advise the user.

Close the door
and/or cover
property.

Check

Are the front
door and/or
delivery cover
closed property?

Is the rated
voltage (100
VAC) present
at the outlet?

Is the power
plug con-
nected to the
outlet?

Step

NO

NO

3

2

1

■

The left door switch goes OFF and, at the same time, the laser shutter closes as

soon as the front left door is opened; as such, put the door switch actuators into left
door switch and laser shutter if the machine needs to be opened with its front left
door open. DO NOT BLOCK THE LASER PATH WITH LIGHT REFLECTING
OBJECTS.

Download free service manual at http://printer1.blogspot.com

«
...
280
281
282
283
284
...
»

Summary of Contents for CP660
























































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP660

Brand: Xerox Pages: 310

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 4

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 16

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 170

Brand: Samsung Pages: 165

Brand: Xerox Pages: 114

Brand: Oki Pages: 94

Brand: Star Pages: 24

Brand: Jolimark Pages: 65

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: SINTERIT Pages: 16

6250N - Phaser Color Laser Printer

Brand: Xerox Pages: 467

Brand: QMS Pages: 188

Brand: Sinfonia Technology Pages: 41

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands