8-6
Section 8: Servicing
Section Rev. February 2009
CLEARING PINS JAMMED IN DISTRIBUTOR
1. Turn the stop/run on the rear mechanic’s box , Nexgen box, or mechanic’s remote display to the
stop position. If possible, turn off the main power switch on the Nexgen Controller box and
remove the incoming 3 phase power.
2. Check for pins jammed at track ejector points. Check for pins jammed at belt turning points.
Remove the jammed pins and place them on the outside return belt track.
3. Check the pin ejector assemblies for proper positions.
4. Continuous jams require checking the pin station assemblies for broken parts. Check pin
release levers.
5. Apply power to the pinsetter.
6. Check pinsetter operation.
STOPPING MACHINE IN MID-CYCLE
A machine may be stopped in mid-cycle by turning the stop/run switch on the Nexgen Controller,
mechanic’s remote display, or mechanic’s box to the stop position. Once power is restored to the
pinsetter it will automatically return to home or ready to bowl position.
If internal service work is to be performed, turn off the main power switch and if possible, disconnect
the incoming 3 phase power. Use an approved lockout device on the main power switch to prohibit the
machine from being turned on.
NOTE:
Removing the incoming 3 phase power will disable both pinsetters. Upon completion
of work, reconnect the 3 phase power, remove any installed lockout devices and turn the main
power switch on.
Once the machine has initialized, turn the stop/run switches to the run position. With older versions of
GS firmware the machine will return to the “ready to bowl” position. With newer firmware a power fail
(PF) error may be displayed. Clear the code by toggling both stop/run switches off then on.
Summary of Contents for GS-X Series
