3-8
Section 3: Nexgen Electronics
Section Rev. February 2017
(1) P15 (Auxiliary Out) -
Not Used
(2) P16 (Auxillary In) -
Communication to a mechanic’s rear display.
(3) P17 (Pin Switches) -
This connection provides input from the pin holder switches and spotting
tong (ST) switch for the right pinsetter.
(4) P18 (Pin Solenoids) -
The pin holder (gripper) solenoids for the right pinsetter are energized
via the voltage sent from this connector.
(5) P19 (Left Side Function Solenoids and Switches) -
This connection provides the input for the
“TS1,” “G,” “EC” and pin count switches and voltage to the sweep release, spotting tong, stroke
limiter and shark solonoids for the even lane pinsetter. It also provides power for the optional
mechanic’s rear display.
(6) P20 (Ball Detect & Foul) -
This connection provides input from the ball detector, foul unit,
and ball rack reset button for the even lane
(7) P21 (Rear Box Control) -
This connection provides input from the even lane pinsetter’s stop/
run switch located on the mechanic’s remote display.
(8) P22 (Masking Unit) -
This connection provides power for 1st and 2nd ball lights on the
masking unit.for the even (right hand) lane.
(9) P23 (Right Side Function Solenoids and Switches,) -
Connection for the switches located on
the right side of the even lane (right) pinsetter. These switches include the “A,” “B,” “C,” “D,”
“SM,” “TS2,” and “OOR.” The connection also provides the voltage for the status light, the ball
door solenoid for the even lane pinsetter.
(10) P24 (Sweep Power) -
Provides full 3-phase power to the even lane pinsetter’s sweep motor.
(11) P25 (Distributor Power) -
Provides 3-phase power to the even lane pinsetter’s distributor
motor.
(12) P26 (Ball Accelerator Power) -
Provides 3-phase power to the ball accelerator motor.
(13) P27 (Table Power) -
Provides 3-phase power to the even lane pinsetter’s table motor.
(14) P28 (Pin Light) -
Provides 208 or 230 VAC single phase to the even lane pinsetter’s pin light.
Summary of Contents for GS-X Series
