3-32
Section 3: Nexgen Electronics
Section Rev. February 2017
(1) Restart Switch -
Button used to restart the Safety Power Controller box after a power failure
or interruption of power caused by opening the guard or masking unit interlock switch or photo
sensors.
(2) Emergency Stop Switch -
Push this button to immediately remove power from the Nexgen box
and shut down power to both pinsetters of the lane pair.
(3) Fuse -
.25A slow blow fuse used to protect power going to the power supply module.
(4) Main Power Switch -
Controls the 3-phase power entering the box. In the off position,
this switch will disconnect power to the Nexgen box and disable both pinsetters and the ball
accelerator.
(5) 3 Phase Power In -
Input power connection for the 3-phase power. This voltage can be 208,
230 or 380 - 415 VAC.
(6) Power Out to Nexgen -
Power conection for 3 phase power to the Nexgen box.
(7) Contactors -
Power contactors used to disconnect 3 phase power whenever the emergency off
switch is pressed or an interlock switch/sensor is tripped
(8) Power Supply -
DC power supply for the photo sensor controller and the photo sensor receiver
and transmitter.
(9) Interlock Switches -
Connection for the masking unit and rear door interlock swithes. The
switches can be plugged into either connector.
(10) Safety Photo Sensor -
Connection for the safety photo sensor located at the front of the
pinsetters. The 3 terminal connector is for the transmitter unit. the 4 terminal connector is for
the receiving unit.
(11) Photo Sensor Controller -
The module that monitors the photo sensor receiver and transmitter
and the interlock switches.
(12) Controller Display -
The photo sensor controller display provides information as to the status
of the module and the interlock switches and photo sensors. Refer to Table 5.
Summary of Contents for GS-X Series
