Bosch Rexroth lndraDrive HCS02 Series Project Planning Manual Download Page 89

Page: 89 / 382

air intake

air outlet

mounting surface in control cabinet

top

distance top

bot

distance bottom

Fig.5-64:

Air intake and air outlet at drive controller

Power Dissipation vs. Output Cur‐

rent

The figure below illustrates the connection between power dissipation and out‐

put current, depending on the switching frequency f

which was set at the drive

controller. See also Parameter Description "P-0-0001, Switching frequency of

the power output stage".

In addition, take the power at the braking resistor and the power

consumption of the control section into account. Both powers are

not contained in the figure.

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG

79/369

Power Sections for Converters - IndraDrive C

Summary of Contents for Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands

Bosch Rexroth lndraDrive HCS02 Series, Project Planning Manual

Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands