Bosch Rexroth lndraDrive HCS02 Series Project Planning Manual Download Page 229

Page: 229 / 382

Connection Diagram with HLB01.1D

CAUTION

Risk of damage to the device!

Establish connection from HMV_X32/8 to HLB_X32/7.
This avoids energy from the mains connection being supplied and the ZKS

stage of the DC bus resistor unit HLB being simultaneously active.
Also applies to HMV01 without integrated ZKS stage and external mains con‐

tactor HMV01.1R-W0120.

Fig.7-44:

Connection diagram HMV01 with HLB01.1D

For other connection diagrams and control circuits for the mains

connection, see the documentation “Rexroth IndraDrive - Drive

System, Project Planning Manual” in the section “Control Circuits

for the Mains Connection”

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG 219/369

IndraDrive M Supply Units

Summary of Contents for Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands

Bosch Rexroth lndraDrive HCS02 Series, Project Planning Manual

Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands