Bosch Rexroth lndraDrive HCS02 Series Project Planning Manual Download Page 271

Page: 271 / 382

An external contact element is required, if motor holding brakes with

higher currents than the allowed current load are to be supplied at

X6.

Coding of the Connectors

At the HMD power sections with two inverter outputs, the outputs

have been coded, i.e. provided with a coding section. This avoids

accidentally interchanging the two cables.
Coding
●

X6.1: coding section at pin 4

●

X6.2: coding section at pin 1

For ready-made Rexroth motor power cables, you therefore have

to code the male connector at the motor power cable accordingly

for X6.1 and X6.2:
●

for connector X6.1: cut off plastic pin 4 at connector

●

for connector X6.2: cut off plastic pin 1 at connector

Fig.8-25:

Coding of X6.1 and X6.2

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG 261/369

Functions and Electrical Connection Points

Summary of Contents for Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands

Bosch Rexroth lndraDrive HCS02 Series, Project Planning Manual

Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands