Bosch Rexroth lndraDrive HCS02 Series Project Planning Manual Download Page 367

Page: 367 / 382

HAS02.1-007 With Power Supply Cable and Mains Filter

fixing device

shielding plate

clip

different possibilities of mounting the shielding plate, according to cable

routing

power supply cable

motor cable

Fig.11-53:

HAS02.1-007 at bottom of mains filter (rated current 80 A / 106 A)

1. Hang up fixing device at bottom of mains filter and fasten with supplied

screws.
2. Screw shielding plate to fixing device.
According to desired cable routing, the shielding plate can be mounted in dif‐

ferent positions
3. Fix shield of cable to shielding plate with clip.

The shield terminals must not be used to provide strain relief.

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG 357/369

Accessories

Summary of Contents for Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands

Bosch Rexroth lndraDrive HCS02 Series, Project Planning Manual

Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands