Bio-Logic HCV-3048 Installation And Configuration Manual Download Page 44 | Manualshive

Page: 44 / 122

background image

Manual for VMP300-based instruments

36

Fig. 42:

“Advanced Ethernet settings” of the

“New Device” window used to change the
instrument IP Address.

Modify the IP Address to have a valid address in your network. Repeat this procedure with the
Gateway and click on “

Modify device

”. Then the new IP Address is sent to the instrument and

a “configuration changed” message appears in green. Several “Bip” sounds are emitted by the
instrument indicating that the communication board is reinitialized with the new IP Address.
“Configuration changed” appears at the bottom of this window.

Fig. 43: New configuration.

Then click “

OK

” to display the “New Device” window and “

Refresh

” to refresh the window and

select your instrument’s IP address. Click on the “Select” button.
Now the instrument is connected and ready for use.

«
...
42
43
44
45
46
...
»

Summary of Contents for HCV-3048



























































































































Reviews:

No comments

Related manuals for HCV-3048

Brand: HANYOUNG NUX Pages: 4

Brand: jenway Pages: 30

Brand: National Meter & Automation Pages: 24

Brand: Lakeshore Pages: 2

Brand: Kamstrup Pages: 4

Brand: Van Walt Pages: 12

Brand: Valhalla Scientific Pages: 43

Brand: LumaSense Pages: 23

XL4 SECOND STAGE

Brand: Apeks Pages: 21

Brand: CryptOn Pages: 13

Brand: Mid-West Pages: 14

Brand: WAGNER Pages: 4

Brand: Cal Test Electronics Pages: 20

Brand: Dairymaster Pages: 14

Brand: Witschi Pages: 50

Brand: Kane Pages: 4

Brand: Elcometer Pages: 19

Brand: Anritsu Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands