Bio-Logic HCV-3048 Installation And Configuration Manual Download Page 73

Page: 73 / 122

Manual for VMP300-based instruments

6.5 Virtual potentiostat

The user can work with the EC-Lab



software without being connected to an instrument. In

that case, the software sees a virtual potentiostat that is not available for experiments but can
be used as a user’s interface. The user can select his virtual instrument in the “

Devices

”

frame,

click on the “

Virtual potentiostat

” button

then, the corresponding software interface will

be displayed.

Fig. 91: Virtual potentiostat button (in the red rectangle).

The available techniques and time base are different depending on the instrument selected.

Fig. 92: Virtual potentiostat window.

Summary of Contents for HCV-3048



























































































































Search results

Summary of Contents for HCV-3048

Reviews:

Related manuals for HCV-3048

Brands by name

Popular brands

Bio-Logic HCV-3048, Installation And Configuration Manual

Search results

Summary of Contents for HCV-3048

Reviews:

Related manuals for HCV-3048

Brands by name

Popular brands