Bio-Logic HCV-3048 Installation And Configuration Manual Download Page 26

Page: 26 / 122

Manual for VMP300-based instruments

Software installation on the computer

Before turning on the instrument, it is recommended to first install the EC-Lab

software and/or

EC-Lab

express. For this operation, insert the CD-Rom in the computer. The installation is

automatically launched with the “Autorun” function. The first software to be installed is EC-
Lab

. If your computer does not have a CD-Rom drive, all software can be downloaded from

the Bio-Logic website at:

http://www.bio-logic.info/electrochemistry-ec-lab/downloads/

3.1 EC-Lab

software installation

Fig. 15: EC-Lab

software installation. Step 1.

Fig. 16: EC-Lab

software installation. Step 2.

Summary of Contents for HCV-3048



























































































































Search results

Summary of Contents for HCV-3048

Reviews:

Related manuals for HCV-3048

Brands by name

Popular brands

Bio-Logic HCV-3048, Installation And Configuration Manual

Search results

Summary of Contents for HCV-3048

Reviews:

Related manuals for HCV-3048

Brands by name

Popular brands