Baumuller b maXX 1000 Parameter Manual Download Page 57

Page: 57 / 210

Parameter

Parameter manual

b maXX

1000

Document no. 5.07004.03

of 208

P0850

The operation mode

P1000

–

must be set to 249 using auto tuning.

Start Auto Tuning by pressing RUN key after this parameter is set to 1 or 2.

When set to 1, it will only auto detect R1 value and

P0110

–

must be input manually.

When set to 2, the b maXX

1000 should be unloaded and the values of

and

will be set automatically.

The steps for AUTO-Tuning are:

Make sure that all the parameters are set to factory settings and the motor wiring is
correct.

Make sure the motor has no-load before executing auto-tuning and the shaft is not con-
nected to any belt or gear motor.

Fill in

an d

values.

is set to 2, the b maXX

1000 will execute

auto-tuning immediately after receiving a „RUN“ command. (Note: The motor will run!).

The total auto tune time will be 15 s

drives need longer accel/decel time (factory setting is recommended). After executing
Auto-tune,

P0850

–

is set to 0.

After executing, please check if there are values filled in

and

. If

not, please press RUN key after setting

P0850

–

again.

Then you can set

P0800

–

to 1 (vector control) and set other parameters according

to your application requirement.

P0850

Selbstoptimierung Motorparameter

0 to 2

Motor auto parameters auto tuning

STOP

BM_u_MotorAutoParaAutoTuning

1:1

Value

Meaning

Disable

Auto tuning R1 (motor doesn’t run)

Auto tuning R1 and no load test (with running motor)

NOTE

In vector control mode it is not recommended to have motors run in parallel.

It is not recommended to use vector control mode if motor rated power exceeds the rated
power of the b maXX

1000.

Summary of Contents for b maXX 1000



















































































































































































































Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands

Baumuller b maXX 1000, Parameter Manual

Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands