Baumuller b maXX 1000 Parameter Manual Download Page 147

Page: 147 / 210

Parameter

Parameter manual

b maXX

1000

Document no. 5.07004.03

147

of 208

P2112

This parameter displays the output power in kW of the terminals U/T1, V/T2, W/T3 to the
motor.

P2113

This parameter displays the estimated value of torque in Nm as it relates to the current.

P2114

The frequency command value is displayed here.

P2115

The actual value of frequency is displayed here.

P2116

This parameter displays the temperature of the IGBT in °C.

P2117

This parameter displays the output current in A supplied to the motor.

P2112

Ausgangsleistung

0.00 to 99.99 kW

Output power

0.00 kW

BM_u_OutputPower

100:1

P2113

Ausgangsmoment

0.00 to 655.35 Nm

Output torque

0.00 Nm

BM_u_OutputTorque

100:1

P2114

Frequenzsollwert

0.00 to 600.00 Hz

Set point frequency

0.00 Hz

BM_u_SetPointFrequency

100:1

P2115

Frequenzistwert

0.00 to 600.00 Hz

Actual output frequency

0.00 Hz

BM_u_ActualFrequency

100:1

P2116

IGBT Temperatur

0.0 to 999.9 °C

IGBT temperature

0.0 °C

BM_u_IGBTTemperature

10:1

P2117

Ausgangsstrom

0.0 to 99.9 A

Output current

0.0 A

BM_u_OutputCurrent

10:1 A

Summary of Contents for b maXX 1000



















































































































































































































Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands

Baumuller b maXX 1000, Parameter Manual

Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands