Baumuller b maXX 1000 Parameter Manual Download Page 29

Page: 29 / 210

Parameter

Parameter manual

b maXX

1000

Document no. 5.07004.03

of 208

P0077

The motor auto tuning procedure will set this parameter. The user may also set this pa-
rameter without using the auto tuning procedure, see

P0850

–

P0110

The rated current of the drive

P0054

–

is regarded as 100 %. The setting of the motor

no-load current will affect the slip compensation.

The setting value must be less than

P0054

–

P0111

Refer to the rated rpm and the number of polepairs on the type plate of the motor and use
the following equation to calculate the rated slip:

Rated slip (Hz) = F

Motor nominal frequ.

(

P0061

–

) - (rated rpm

⋅

motor pole pairs

⋅

120)/60

This parameter is valid only in vector mode.

P0111

–

can be calculated via

P0124

–

automatically if unknown.

P0111

–

can be

changed only if

P0124

–

= 0.

P0112

This parameter may be set so that the drive will increase its voltage output to obtain a
higher torque. Only to be used for V/f control mode.

P0077

Motor Ständerwiderstand

0 to 65535 m

abc

Motor line-to-line resistance

0 m

abc

STOP

BM_u_MotorStatorResist

1:1

abc

P0110

Motor Leerlauf-Strom

0.0 to 99.0 %

P0054

–

Motor no-load current

40.0 %

P0054

–

BM_u_MotorNoLoadCurrent

10:1

P0111

Motor Nennschlupf

0.00 to 20.00 Hz

Motor rated slip (Motor nominal slip)

3.00 Hz

STOP

BM_u_MotorRatedSlip

100:1

P0112

Drehmomentanpassung

0.0 to 10.0 Hz

Torque compensation

0.0 Hz

BM_u_TorqueComp

10:1

NOTE

Too high torque compensation can overheat the motor.

Summary of Contents for b maXX 1000



















































































































































































































Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands

Baumuller b maXX 1000, Parameter Manual

Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands