Baumuller b maXX 1000 Parameter Manual Download Page 184

Page: 184 / 210

Basic of CAN

Parameter manual

b maXX

1000

Document no. 5.07004.03

Baumüller Nürnberg GmbH

184

of 208

B.3

Responses to errors

Invalid SDO access is refused with abort codes. The structure of these abort message frames is identical
to the

SDO message frame

. The data field contains an abort code 4 bytes long.

With invalid accesses to communication-specific objects (1xxx

hex

), the following messages are differenti-

ated:

Invalid accesses to all other objects (2XXX

hex

and 6XXX

hex

) are globally refused with the following codes:

Abort code

Meaning

hex

Inconsistent parameters (toggle bit has not changed)

hex

Writing to write-protected object

hex

Object does not exist

hex

Data cannot be mapped

(e. g. incorrect length indication)

hex

Hardware access error

(save/load from flash memory)

hex

Access to flash memory concerning hardware fault failed

hex

Incorrect length data value

hex

Subindex does not exist

hex

Value range exceeded (during write accesses)

hex

Value too high (during write accesses)

hex

Data cannot be transferred or saved to the application

hex

Data cannot be mapped due to the current communication
state

(e. g. change mapping in the OPERATIONAL state).

Abort code

Meaning

hex

Error in data format

hex

Element cannot be changed

hex

Element not present

hex

Value too high (during write accesses)

hex

Value too low (during write accesses)

hex

General error occurred

hex

Data not available at present

Summary of Contents for b maXX 1000



















































































































































































































Search results

Summary of Contents for b maXX 1000

Reviews:

Brands by name

Popular brands

Baumuller b maXX 1000, Parameter Manual

Search results

Summary of Contents for b maXX 1000

Reviews:

Brands by name

Popular brands