auto maskin DCU 408 Installation And Configuration Manual Download Page 81

Page: 81 / 111



DCU 410 Engine Panel Installation

400 Series Installation and Configuration

Home

–

DCU

–

Miscellaneous

Alarm Configuration

The DCU has a primary and a secondary power supply

input.

If the secondary input is not in use, the low voltage alarm

on this input needs to be disabled.

Primary Power Fail Alarm Enabled



Set to No to disable the alarm. This is used when

there is no connection to the primary supply.



Set to Yes to enable the alarm. This is used when

there is a connection to the primary supply.

Typical setting:



Yes. Normally, there shall be a separate supply

connected to the primary supply.

Secondary Power Fail Alarm Enabled



Set to No to disable the alarm. This is used when

there is no connection to the secondary supply.



Set to Yes to enable the alarm. This is used when

there is a connection to the secondary supply.

Typical setting:



Yes. Normally, there shall be a separate supply

connected to the secondary supply.

J1939 CAN bus Broken Wire Alarm When Engine Not

Running

Default setting is No.

J1939 CAN bus Nodes Lost Warning Enabled:

Default setting is No.

Erratic J1939 Data Warning Enabled:

Default setting is No.

Summary of Contents for DCU 408
















































































































Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands

auto maskin DCU 408, Installation And Configuration Manual

Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands