auto maskin DCU 408 Installation And Configuration Manual Download Page 38

Page: 38 / 111

400 Series Installation and Configuration

DCU 410 Engine Panel Installation



Change the IP-addresses until all units have a unique

address.

Web Server Configuration

Once logged in, the DCU can be configured. The following

are the Web Server main menu items.

Home

When logged in, the browser displays the following.

The Home screen lists the following menu items.

DCU

This is the top level menu for the entire DCU 410 (or DCU

408) configuration.

The configuration is saved in the configuration file,

located in the DCU.

RIO

This is the top level menu for the optional expansion I/O

modules RIO 410.

The configuration is saved in the DCU configuration file.

Summary of Contents for DCU 408
















































































































Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands

auto maskin DCU 408, Installation And Configuration Manual

Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands