auto maskin DCU 408 Installation And Configuration Manual Download Page 75

Page: 75 / 111



DCU 410 Engine Panel Installation

400 Series Installation and Configuration

Home

–

DCU

–

User Interface

Language

In this section, the signal descriptions can be manually

translated to other languages.

All Signals

Press All Signals to display all signals available in the

DCU.

The page displays three rows of signal text. The first row

is the

English

Default

text, the second row is the

English

Used

text, and the third row is the 2nd language.

English Default

English Used

2nd Language

Engine Oil Press.

Engine Oil

Pressure

Motoroljetrykk

Engine Speed

[default]

Motorturtall

Note! The English language is always available in the DCU

and the RP.

The text [default] means that the English default text

(column 1) will be used. Select any [default] text to

change the signal text description.

Enabled Signals Only

This is the same as All Signals, except that only signals

that are in use are listed.

Summary of Contents for DCU 408
















































































































Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands

auto maskin DCU 408, Installation And Configuration Manual

Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands