auto maskin DCU 408 Installation And Configuration Manual Download Page 67

Page: 67 / 111



DCU 410 Engine Panel Installation

400 Series Installation and Configuration

Choose a Template

A range of templates will be presented. Choose a

template and start populating the page with predefined

signals.

The chosen template will appear at the bottom of the

screen. Select a signal and Submit it to clear away the

other templates.

Delete a Page

First Select the page, and then press the Delete button.

The pages will be renumbered!

Edit the Signal

If the chosen signal is not correctly configured, press Edit

Signal to edit it.

RP Home View Configuration

The RP 410 home page displays certain parameters from

each connected DCU.

This is configured in each DCU.

Summary of Contents for DCU 408
















































































































Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands

auto maskin DCU 408, Installation And Configuration Manual

Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands