auto maskin DCU 408 Installation And Configuration Manual Download Page 33

Page: 33 / 111



DCU 410 Engine Panel Installation

400 Series Installation and Configuration

Configuration of the DCU

The configuration of the DCU is outlined in this section.

Configuration- and Firmware files

The DCU may be configured in one of the following three

ways:

DCU Web Server Configuration Interface

The DCU has an inbuilt web server, offering access to full

configuration of the DCU.

Note! This is the primary configuration interface.

Approved browsers

The following browsers are approved for use. Other

browsers and versions may work.

Browser

Version

Internet Explorer™

7 or higher

Firefox™

5 or higher

Chrome™

13 or higher

DCU User Interface Menu

For quick and easy changes to the configuration, there is

a configuration entry point in the menu.

Note! This manual will not describe the panel menu

configuration interface in detail. Only the web server

menu operation is covered.

USB Memory Interface

Insert a USB memory with the configuration file(s) and

follow the guidelines appearing on the DCU screen.

Note! The configuration file name can only contain the

following characters:

Summary of Contents for DCU 408
















































































































Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands

auto maskin DCU 408, Installation And Configuration Manual

Search results

Summary of Contents for DCU 408

Reviews:

Related manuals for DCU 408

Brands by name

Popular brands