Applied Innovation AISwitch AI2524 User Manual Download Page 90

Page: 90 / 418

AI2524 Router Card User’s Manual

Page 5-24

August 1997

2524UM

Default client IP address for this interface [172.16.72.19]:

The following configuration command script was created:

hostname Router

enable secret 5 $1$krIg$emfYm/1OwHVspDuS8Gy0K

enable password ww

line vty 0 4

password ww

snmp-server community public

no decnet routing

appletalk routing

ipx routing

ip routing

line 1 16

speed 57600

flowcontrol hardware

modem inout

arap network 20 ARA Dialins

line 1 16

arap enable

autoselect

! Turn off IPX to prevent network conflicts.

interface Ethernet0

no ipx network

interface Serial0

no ipx network

interface Serial1

no ipx network

interface Ethernet0

ip address 172.16.72.2 255.255.255.0

appletalk cable-range 1-1 1.204

appletalk zone Sales

ipx network 1

no mop enabled

interface Serial0

no shutdown

no ip address

ip unnumbered Ethernet0

appletalk cable-range 3-3

appletalk zone ZZ Serial

ipx network 3

no mop enabled

interface Serial1

no ip address

ip unnumbered Ethernet0

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Search results

Summary of Contents for AISwitch AI2524

Reviews:

Applied Innovation AISwitch AI2524, User Manual, Page: 90 / 418

Search results

Summary of Contents for AISwitch AI2524

Reviews: